Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT AIRBAG SENSOR
REMOVAL
Removal / installation · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.
PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here ).
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here ).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
3.
DRAIN ENGINE COOLANT
for 1TR-FE (Click here )
for 2TR-FE (Click here )
for 1KD-FTV (Click here )
for 2KD-FTV (Click here )
for 5L-E (Click here )
4.
REMOVE UPPER RADIATOR SUPPORT SEAL (w/o Intercooler)
for 1TR-FE (Click here )
for 2TR-FE (Click here )
for 2KD-FTV (Click here )
for 5L-E (Click here )
5.
REMOVE NO. 1 AIR INLET DUCT (w/ Intercooler)
for 1KD-FTV (Click here )
for 2KD-FTV (Click here )
6.
REMOVE RADIATOR GRILLE
Put protective tape around the radiator grille.
Text in Illustration
*1
Protective Tape
Remove the 4 clips and 2 screws.
Detach the 8 claws and remove the radiator grille.
7.
REMOVE STEP PLATE COVER LH
Remove the 4 clips.
Detach the claw and remove the step plate cover LH.
8.
REMOVE STEP PLATE COVER RH
HINT:
Use the same procedure described for the LH side.
9.
REMOVE FRONT BUMPER COVER
Put protective tape around the front bumper cover.
Remove the 3 bolts and 6 clips.
w/ Fog Light: Disconnect the No. 4 engine room wire connector.
Remove the 3 bolts and 6 clips.
Text in Illustration
*1
Protective Tape
-
-
Detach the 7 claws and guide.
HINT:
Use the same procedure for the RH side.
Remove the front bumper cover.
10.
REMOVE RADIATOR RESERVE TANK ASSEMBLY
Slide the hose clamp and disconnect the water by-pass hose from the radiator reservoir assembly.
Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator reservoir assembly.
Remove the bolt and radiator reservoir assembly
11.
REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
for 1TR-FE (Click here )
for 2TR-FE (Click here )
for 1KD-FTV (Click here )
for 2KD-FTV (Click here )
for 5L-E (Click here )
12.
REMOVE HOOD LOCK ASSEMBLY
Remove the 3 bolts and disconnect the hood lock assembly.
Remove the hood lock assembly from the hood lock control cable assembly.
13.
REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY
Remove the 3 bolts and hood lock support brace sub-assembly.
Text in Illustration
*A
for Standard Body
*B
for Wide Body
14.
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.
Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
Text in Illustration
*A
for LHD
*B
for RHD
Remove the 6 bolts and upper radiator support sub-assembly.
15.
REMOVE FRONT AIRBAG SENSOR LH
Disconnect the connector.
Remove the 2 bolts and front airbag sensor LH.