2014-2019 Hiace · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. DRAIN ENGINE COOLANT
  1. for 1TR-FE (Click here)
  2. for 2TR-FE (Click here)
  3. for 1KD-FTV (Click here)
  4. for 2KD-FTV (Click here)
  5. for 5L-E (Click here)

4. REMOVE UPPER RADIATOR SUPPORT SEAL (w/o Intercooler)
  1. for 1TR-FE (Click here)
  2. for 2TR-FE (Click here)
  3. for 2KD-FTV (Click here)
  4. for 5L-E (Click here)

5. REMOVE NO. 1 AIR INLET DUCT (w/ Intercooler)
  1. for 1KD-FTV (Click here)
  2. for 2KD-FTV (Click here)

6. REMOVE RADIATOR GRILLE

  1. B366619E01
    Put protective tape around the radiator grille.
    Text in Illustration 
    *1
    Protective Tape

  1. B361905
    Remove the 4 clips and 2 screws.

  1. Detach the 8 claws and remove the radiator grille.


7. REMOVE STEP PLATE COVER LH

  1. B260281
    Remove the 4 clips.

  1. Detach the claw and remove the step plate cover LH.


8. REMOVE STEP PLATE COVER RH

HINT:
Use the same procedure described for the LH side.


9. REMOVE FRONT BUMPER COVER
  1. Put protective tape around the front bumper cover.

  1. Remove the 3 bolts and 6 clips.

  1. w/ Fog Light:
    Disconnect the No. 4 engine room wire connector.

  1. Remove the 3 bolts and 6 clips.

    B361908E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. B361909
    Detach the 7 claws and guide.

    HINT:
    Use the same procedure for the RH side.

  1. Remove the front bumper cover.


10. REMOVE RADIATOR RESERVE TANK ASSEMBLY

  1. A316482
    Slide the hose clamp and disconnect the water by-pass hose from the radiator reservoir assembly.

  1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator reservoir assembly.

  1. Remove the bolt and radiator reservoir assembly


11. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
  1. for 1TR-FE (Click here)
  2. for 2TR-FE (Click here)
  3. for 1KD-FTV (Click here)
  4. for 2KD-FTV (Click here)
  5. for 5L-E (Click here)

12. REMOVE HOOD LOCK ASSEMBLY

  1. A243233
    Remove the 3 bolts and disconnect the hood lock assembly.

  1. Remove the hood lock assembly from the hood lock control cable assembly.


13. REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

  1. E289333E01
    Remove the 3 bolts and hood lock support brace sub-assembly.
    Text in Illustration 
    *A
    for Standard Body
    *B
    for Wide Body


14. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
  1. Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.

  1. Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

    A316483E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. Remove the 6 bolts and upper radiator support sub-assembly.


15. REMOVE FRONT AIRBAG SENSOR LH

  1. C101570
    Disconnect the connector.

  1. Remove the 2 bolts and front airbag sensor LH.

← REMOVAL (Apr 2016 – Dec 2016)INSTALLATION (Oct 2014 – Dec 2014) →