2014-2019 Hiace · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


1. INSTALL MASTER CYLINDER PUSH ROD CLEVIS
  1. Temporarily install the push rod clevis with the lock nut.

  1. C113674
    Turn the push rod clevis and adjust length "A" shown in the illustration.

    Length "A":
    163.6 to 173.6 mm (6.441 in. to 6.835 in.)

  1. Tighten the push rod lock nut.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


2. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY
  1. Install the grommet and check valve assembly.


3. INSTALL VACUUM WARNING SWITCH ASSEMBLY
  1. Clean the vacuum warning switch assembly.

  1. Apply seal packing black to 2 or 3 threads of the bolts.

    Seal packing:
    Seal packing black or equivalent

  1. Install the warning switch assembly to the brake booster.

    Torque:
    13.7 N*m{ 140 kgf*cm , 10 ft.*lbf }


4. INSTALL BRAKE BOOSTER GASKET
  1. Install a new brake booster gasket to the brake booster.


5. INSTALL BRAKE BOOSTER ASSEMBLY

  1. C102541
    Install the brake booster assembly with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. C106100E02
    Connect the vacuum hose with the clip.

  1. for 2KD-FTV, 5L-E engine type:
    Connect the vacuum warning switch connector to the brake booster assembly.


6. INSTALL BRAKE TUBE
  1. for Automatic transmission:
    Connect the 2 tubes to the clamp.

  1. for Manual transmission:

    1. C106102
      Connect the 3 tubes to the clamp.

    2. C113662
      Using a union nut wrench, connect the clutch tube to the clutch master cylinder.

      Torque:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }

      NOTICE:
      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


7. INSTALL MASTER CYLINDER PUSH ROD CLEVIS

  1. C105607E10
    Apply a light coat of lithium soap base glycol grease to the clevis pin.

  1. Install the push rod clevis to the brake pedal support assembly with the clevis pin and a new clip.


8. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER
(Click here)

9. INSTALL HEADLIGHT ASSEMBLY RH (for RHD with Standard Body)

HINT:
Install of the headlight assembly RH is the same as the headlight assembly LH.

  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


10. INSTALL HEADLIGHT ASSEMBLY RH (for RHD with Wide Body)

HINT:
Install of the headlight assembly RH is the same as the headlight assembly LH.

  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


11. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (for LHD with Standard Body)
(Click here)

12. INSTALL RADIATOR GRILLE (for LHD with Standard Body)
(Click here)

13. INSTALL BRAKE MASTER CYLINDER
(Click here)

14. ADD BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3 or equivalent


15. BLEED BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C106089
    Using a union nut wrench, disconnect the brake lines from the master cylinder.

  1. Slowly depress the brake pedal and hold it there.

  1. C106090
    Block the outer holes with your fingers, and release the brake pedal.

  1. Remove your fingers. Slowly depress the brake pedal and hold it again. Block the outer holes with your fingers and release the brake pedal. Repeat this procedure 3 or 4 times.

  1. Using a union nut wrench, connect the brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


16. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


17. INSPECT BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No.116 DOT3 or equivalent


18. CHECK BRAKE FLUID LEAKAGE

19. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT
  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


20. PREPARATION FOR HEADLIGHT AIMING (USING A SCREEN)
  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


21. INSPECT HEADLIGHT AIMING
  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


22. ADJUST HEADLIGHT AIMING
  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


23. INSPECT BRAKE PEDAL HEIGHT

  1. C102528E01
    Check brake pedal height.

    Pedal height from floor:
    151 to 161 mm (5.945 to 6.339 in.) for left hand drive
    154 to 164 mm (6.063 to 6.457 in.) for right hand drive


24. ADJUST BRAKE PEDAL HEIGHT
  1. Disconnect the stop light switch connector.

  1. Turn the stop light switch assembly counter-clockwise and remove it.

  1. Remove the brake booster (Click here).

  1. Loosen the push rod lock nut.

  1. Adjust the pedal height by turning the pedal push rod clevis.

  1. Tighten the push rod lock nut.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }

  1. Install the brake booster (Click here).

  1. F049043E03
    Insert the stop light switch into the adjuster until it slightly touches the cushion.

    CAUTION:
    Do not depress the brake pedal.

  1. F049044E06
    Turn the stop light switch assembly clockwise by approximately 90°.

    CAUTION:
    Do not depress the brake pedal.

  1. Connect the stop light switch connector.

  1. Check the clearance of the shaft.

    Clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)


25. INSPECT BRAKE PEDAL FREE PLAY
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. F048932E03
    Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)


26. INSPECT BRAKE PEDAL RESERVE DISTANCE
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Release the parking brake handle.

  1. C102776E01
    With the engine running, depress the pedal and measure the pedal reserve distance as shown in the illustration.

    Pedal reserve distance from floor:
    More than 117 mm (4.61 in.) at 500 N (51 kgf, 112.5 lbf) for left hand drive
    More than 120 mm (4.72 in.) at 500 N (51 kgf, 112.5 lbf) for right hand drive

    NOTICE:
    Remove the floor mat before measuring the distance.

← INSPECTION (from Oct 2014)INSTALLATION (Jan 2015 – Dec 2016) →