2014-2019 Hiace · Service Manual ENGINE

P1220 Timer Control Circuit

Diagnostic trouble codes · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection or supply pump assembly and controls the internal fuel pressure of the pump through duty control.
The ECM detects the injection advance angle based on the TDC and NE signals.
DTC No.
DTC Detection Condition
Trouble Area
P1220
During and after engine warm up, actual injection timing is different from target value of ECM calculated for several second.
  1. Open or short in timing control valve circuit
  2. Timing control valve
  3. Fuel filter element sub-assembly (Clogging)
  4. Fuel (Freezing, air present)
  5. Injection or supply pump assembly (Internal pressure and timing control valve)
  6. ECM

WIRING DIAGRAM

A320269E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT TIMING CONTROL VALVE

  1. A105093E01
    Disconnect the timer control valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    10 to 14 Ω



NG
REPLACE TIMING CONTROL VALVE
OK


2. INSPECT TIMING CONTROL VALVE (POWER SOURCE)

  1. A137676E05
    Disconnect the timing control valve connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D61-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Timing Control Valve)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TIMING CONTROL VALVE - NO. 1 INTEGRATION RELAY)
OK


3. CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)
  1. Disconnect the timing control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D61-2 - D100-42 (TCV)
    Always
    Below 1 Ω
    D61-2 or D100-42 (TCV) - Body ground
    Always
    10 kΩ or higher



NG
END
OK


4. CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
  1. Check the fuel filter element sub-assembly assembly (Click here).



NG
REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY (Click here)
OK


5. CHECK FUEL LEAK
  1. Visually check the injection or supply pump assembly, each injector and fuel line for fuel leaks.

    OK:
    No leakage



NG
REPAIR FUEL LEAK
OK


6. REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
  1. Replace the injection or supply pump assembly (Click here).


NEXT


7. CHECK READ OUTPUT DTC (DTC P1220 IS OUTPUT AGAIN)
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Idle the engine for 20 sec. or more.

  1. Read the DTC (Click here).

    Result:
    Display (DTC output)
    Proceed to
    DTC P1220 is output again
    A
    No DTC output
    B



B
END
A

REPLACE ECM (Click here)


← P1220 Timer Control Circuit (Oct 2014 – Dec 2014)P1222 Throttle Motor Circuit Range/Performance (from Oct 2014) →