2014-2019 Hiace · Service Manual ENGINE

P1222 Throttle Motor Circuit Range/Performance

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

Throttle control motor is operated by the ECM and opens and closes the throttle valve.
The fully open position of the throttle valve is detected by the throttle open switch which is mounted on the venturi assembly.
If this DTC is stored, the ECM shuts down the power for the throttle control motor.
DTC No.
DTC Detection Condition
Trouble Area
P1222
Open or short in throttle control motor circuit.
  1. Open or short in throttle control motor circuit
  2. Throttle control motor (Venturi assembly)
  3. Intake restrictor valve
  4. Open or short in throttle open switch circuit
  5. Throttle open switch (Venturi assembly)
  6. ECM
Open or short in throttle open switch circuit.

WIRING DIAGRAM

A320270E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT THROTTLE OPEN SWITCH

  1. A106810E01
    Disconnect the throttle open switch connector.

  1. Remove the venturi assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Throttle valve is opened
    Below 1 Ω
    1 - 2
    Throttle valve is closed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Throttle Open Switch)

    HINT:
    The throttle open switch is integrated with the venturi assembly. If the throttle open switch is replaced, the venturi assembly must be replaced in whole.



NG
REPLACE VENTURI ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (THROTTLE OPEN SWITCH - BODY GROUND, ECM - THROTTLE OPEN SWITCH)
  1. Disconnect the throttle open switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D63-2 - D100-57 (THOP)
    Always
    Below 1 Ω
    D63-1 - Body ground
    Always
    Below 1 Ω
    D63-2 or D100-57 (THOP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK TERMINAL VOLTAGE (THROTTLE CONTROL MOTOR)

  1. A221614E54
    Disconnect the throttle control motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D58-2 (+B1) - Body ground
    Ignition switch ON
    11 to 14 V
    D58-5 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle Control Motor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - NO. 1 INTEGRATION RELAY)
OK


4. INSPECT THROTTLE CONTROL MOTOR

  1. A031135E05
    Disconnect the throttle control motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (LU-B) - 2 (+B1)
    20°C (68°F)
    18 to 22 Ω
    2 (+B1) - 3 (LU+B)
    20°C (68°F)
    18 to 22 Ω
    4 (LU-A) - 5 (+B2)
    20°C (68°F)
    18 to 22 Ω
    5 (+B2) - 6 (LU+A)
    20°C (68°F)
    18 to 22 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Throttle Control Motor)

    HINT:
    The throttle control motor is integrated with the venturi assembly. If the throttle control motor is replaced, the venturi assembly must be replaced in whole.



NG
REPLACE VENTURI ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
  1. Disconnect the throttle control motor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D58-6 (LU+A) - D100-46 (LU+A)
    Always
    Below 1 Ω
    D58-4 (LU-A) - D100-85 (LU-A)
    Always
    Below 1 Ω
    D58-3 (LU+B) - D100-84 (LU+B)
    Always
    Below 1 Ω
    D58-1 (LU-B) - D100-43 (LU-B)
    Always
    Below 1 Ω
    D58-6 (LU+A) or D100-46 (LU+A) - Body ground
    Always
    10 kΩ or higher
    D58-4 (LU-A) or D100-85 (LU-A) - Body ground
    Always
    10 kΩ or higher
    D58-3 (LU+B) or D100-84 (LU+B) - Body ground
    Always
    10 kΩ or higher
    D58-1 (LU-B) or D100-43 (LU-B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P1220 Timer Control Circuit (from Jan 2015)P1225 Spill Control Circuit (from Oct 2014) →