2014-2019 Hiace · Service Manual ENGINE

P0180 Fuel Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes the resistance value according to the fuel temperature. The lower the fuel temperature, the greater the thermistor resistance value, and the higher the fuel temperature, the lower the thermistor resistance value (See Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via a resistor R. That is, resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with changes in the fuel temperature, the potential at the terminal THF also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during low engine revolution and high fuel temperature.
A071307E01
DTC No.
DTC Detection Condition
Trouble Area
P0180
Open or short in fuel temperature sensor circuit for 0.5 seconds or more.
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM

WIRING DIAGRAM

A311404E10

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (FUEL TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

  1. Read the value.

    Result:
    Display
    Proceed
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    The same as actual fuel temperature
    C

    HINT:
    1. If there is an open circuit, the GTS indicates -40°C (- 40°F).
    2. If there is a short circuit, the GTS indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

  1. A204471E33
    Disconnect the fuel temperature sensor connector.

  1. Connect terminals 2 and 1 of the fuel temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Fuel Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Fuel Temperature Sensor)



NG
Go to step 3
OK

REPLACE FUEL TEMPERATURE SENSOR

3. CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D46-2 - D100-72 (THF)
    Always
    Below 1 Ω
    D46-1 - D100-95 (ETHF)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

  1. A204586E01
    Disconnect the fuel temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Fuel Temperature Sensor
    *2
    ECM

  1. Reconnect the fuel temperature sensor connector.



NG
Go to step 5
OK

REPLACE FUEL TEMPERATURE SENSOR

5. CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D46-2 or D100-72 (THF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0115 Engine Coolant Temperature Circuit (from Jan 2015)P0180 Fuel Temperature Sensor "A" Circuit (from Jan 2015) →