P0180 Fuel Temperature Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built from Jan 2015
Versions by build date: Oct 2014 – Dec 2014 from Jan 2015
DESCRIPTION
The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes the resistance value according to the fuel temperature. The lower the fuel temperature, the greater the thermistor resistance value, and the higher the fuel temperature, the lower the thermistor resistance value (See Fig. 1).The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via a resistor R. That is, resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with changes in the fuel temperature, the potential at the terminal THF also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during low engine revolution and high fuel temperature.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0180 |
Open or short in fuel temperature sensor circuit for 0.5 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING GTS (FUEL TEMPERATURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
- Result:
Display
Proceed
-40°C (-40°F)
A
140°C (284°F) or more
B
The same as actual fuel temperature
C
- HINT:
- If there is an open circuit, the GTS indicates -40°C (- 40°F).
- If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
- If there is an open circuit, the GTS indicates -40°C (- 40°F).
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN) |
Disconnect the fuel temperature sensor connector.

Connect terminals 2 and 1 of the fuel temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
- OK:
- 140°C (284°F) or higher
Text in Illustration *1
Fuel Temperature Sensor
*2
ECM
*a
Front view of wire harness connector
(to Fuel Temperature Sensor)
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D46-2 - D100-72 (THF)
Always
Below 1 Ω
D46-1 - D100-95 (ETHF)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Disconnect the fuel temperature sensor connector.

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
- OK:
- -40°C (-40°F)
Text in Illustration *1
Fuel Temperature Sensor
*2
ECM
Reconnect the fuel temperature sensor connector.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D46-2 or D100-72 (THF) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
