2014-2019 Hiace · Service Manual ENGINE

P0443 Evaporative Emission Control System Purge Control Valve Circuit

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the EVAP VSV so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC No.
DTC Detection Condition
Trouble Area
P0443
  1. All of the following conditions (a) are met (1 trip detection logic)
    1. The target control value and actual control value do not match for 10 seconds or more.
    2. The target control value and actual control value do not match for 80 times or more.
  1. Open or short in EVAP VSV circuit
  2. EVAP VSV
  3. ECM

WIRING DIAGRAM

A312577E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

  1. A172375E06
    Connect the intelligent tester to the DLC3.

  1. Disconnect the vacuum hose (charcoal canister side) from the EVAP VSV.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. Place your finger on port E. Check if the disconnected port applies suction to your finger when operating the EVAP VSV using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    EVAP VSV port applies suction to finger
    VSV OFF
    EVAP VSV port applies no suction to finger



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT EVAP VSV
  1. Inspect the EVAP VSV (Click here).



NG
REPLACE EVAP VSV (Click here)
OK


3. INSPECT EVAP VSV (POWER SOURCE)

  1. A161605E54
    Disconnect the EVAP VSV connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to EVAP VSV)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (EVAP VSV - ECM)
  1. Disconnect the EVAP VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D28-1 - D97-62 (PRG)
    Always
    Below 1 Ω
    D28-1 or D97-62 (PRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

  1. Idle the engine for 15 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0443.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P0443 is output)
    B

    HINT:
    If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes and check the DTC judgment result again.



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0420 Catalyst System Efficiency Below Threshold (Bank 1) (from Dec 2017)P0500 Vehicle Speed Sensor (from Oct 2014) →