2014-2019 Hiace · Service Manual ENGINE

Lack of Power or Hesitation

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Malfunction Condition
Main Trouble Area
Related Trouble Area
  1. Lack of power caused by abnormal fuel injection volume (fuel supply pump malfunction, injector assembly malfunction, etc.)
  2. Lack of power caused by intake air volume shortage (turbocharger malfunction, or front exhaust pipe or exhaust manifold converter blocked)
(a) Injector assembly malfunctions
  1. Injector sliding malfunction
  2. Injector stuck closed
  3. Injector stuck open
  4. Deposits in injector
  5. Injector circuit malfunction
(b) Abnormal common rail pressure
  1. Fuel supply pump
(c) Abnormal intake air volume
  1. Intake air system leakage or clogged
  2. Turbocharger
  3. Front exhaust pipe blockage
  4. Exhaust manifold converter blockage
  5. Throttle valve does not open
  1. Pressure limiter
  2. Intake air system blockage
  3. Fuel filter is clogged
  4. Throttle valve
  5. Compression pressure
  6. Injector compensation code
  7. Fuel leak
  8. Glow plug
  9. Fuel pressure sensor
  10. Manifold absolute pressure sensor
  11. Vacuum hose connection for manifold absolute pressure sensor
  12. Injector driver (P0200 stored simultaneously)
  13. Vehicle modifications
  14. Clutch disc wear
  15. Low quality fuel
  16. Frozen fuel
  17. ECM

HINT:
  1. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
  2. Check that the vehicle has not been modified in any way prior to the vehicle inspection.
  3. This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Intake System 
    Symptom and Corresponding Main Fault
    1. Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct
    2. Black smoke (no lack of power) due to leakage between the turbo and intake manifold
    Data List
    MAP
    Turbocharger System 
    Main fault
    1. Air leak in the turbocharged air passage
    2. Turbocharger (turbine, bearing)
    Symptoms
    Lack of power (when vehicle is starting, under heavy load)
    (Black smoke is not emitted when racing while vehicle is stopped)
    Data List
    MAP
    1. If there are problems with waste gate valve operation or the valve is stuck closed, the boost pressure increases. When this happens, the fuel injection amount may be reduced to protect the engine, which may result in a lack of power or hesitation.
    2. With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
    3. Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.
    Exhaust System 
    Main fault
    Blockage
    Symptoms
    Lack of power (high engine speed, under heavy load)
    Glow System 
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Measure the resistance of the glow plug
    Engine - 1 
    Main fault
    Damaged, seized up
    Symptoms
    Cannot crank, crank speed is low, strange noise
    Engine - 2 
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl#
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.

  2. Diesel Injection

    Fuel supply pump 
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Common Rail Pressure, Target Common Rail Pressure
    1. Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
    2. If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa, then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
    Fuel Filter 
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Common Rail Pressure, Target Common Rail Pressure
    1. Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
    2. If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa, then idling will be rough.

    HINT:
    The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
    Injector Assembly 
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.
    Injector Driver 
    Main fault
    Circuit fault: The injector assembly does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as injector assembly
    Diagnostic Trouble Code
    When the injector driver has a fault, some DTCs may be stored.
    Fuel Pressure Sensor 
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Common Rail Pressure, Target Common Rail Pressure
    1. Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
    2. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (Common Rail Pressure decreases to a value less than Target Common Rail Pressure).
    Diagnostic Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.
    Irregular Fuel 
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel Throttle

    Diesel Throttle System 
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position (fully closed: 100%, fully open: 0%)
    2. When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.


Data List Related to Lack of Power
  1. Engine Speed
  2. MAP
  3. Intake Air
  4. Coolant Temp
  5. Target Common Rail Pressure
  6. Common Rail Pressure
  7. Target Pump SCV Current
  8. Injection Feedback Val #1 (to #4)
  9. Injection Volume
  10. Actual Throttle Position

INSPECTION PROCEDURE


Explanation of Symptom
Lack of Power
The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air.
The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector assembly is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure.

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).


1. READ OUTPUT DTC (RELATING TO ENGINE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    No DTCs are output
    A
    Engine related DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2)
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Lack of Power.

  1. With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
    2. The shift lever should be in neutral and the A/C switch and all accessory switches should be off.


NEXT


3. TAKE SNAPSHOT DURING LACK OF POWER (PROCEDURE 3)
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Lack of Power.

  1. Take a snapshot of the Data List items with the GTS during lack of power.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
    2. Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator pedal fully depressed so that the engine speed is around 3000 rpm (obey all laws and regulations, and pay attention to traffic conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever should be in neutral and the A/C switch and all accessory switches should be off).

  1. Check for a lack of power during the driving test.

    Result 
    Result
    Proceed to
    Apparent lack of power is present
    A
    Apparent lack of power is not present
    B



B
Go to step 44
A


4. CHECK SNAPSHOT (MAP)
  1. Check MAP in the snapshot taken in procedure 2 when the engine was running at 4000 rpm with no load.

    Result 
    Result
    Proceed to
    Except below*1
    A
    MAP is below 90 kPa*2
    B
    MAP is 210 kPa or higher*3
    C

    HINT:
    The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
    Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
    *1: There may be a problem in the intake system or fuel system.
    *2: There may be a problem in the turbocharger system.
    *3: There may be a problem in the turbocharger (waste gate valve).



B
Go to step 9

C
Go to step 6
A


5. CHECK SNAPSHOT (COMMON RAIL PRESSURE, TARGET COMMON RAIL PRESSURE AND MAP)
  1. Check Common Rail Pressure, Target Common Rail Pressure and MAP in the snapshot taken in procedure 3 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear and the engine speed around 3000 rpm.

    Result 
    Result
    Proceed to
    MAP is 230 kPa or higher at an engine speed of 3000 rpm
    A
    Difference between Common Rail Pressure and Target Common Rail Pressure is 20000 kPa or more
    B
    Except above
    C

    HINT:
    1. The above values are applicable under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
      Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
    2. The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
    3. If the turbocharger movement is not smooth, etc., the value of MAP in the snapshot taken during lack of power will not reach the target value.
      When the accelerator pedal is fully depressed and the engine speed is 3000 rpm, MAP should be higher than 230 kPa.



B
Go to step 18

C
Go to step 27
A


6. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-2 (PIM) - D105-117 (PIM)
    Always
    Below 1 Ω
    D51-3 (VC) - D105-93 (VCPM)
    Always
    Below 1 Ω
    D51-1 (E) - D105-116 (EPIM)
    Always
    Below 1 Ω
    D51-2 (PIM) or D105-117 (PIM) - Body ground
    Always
    10 kΩ or higher
    D51-3 (VC) or D105-93 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D51-1 (E) or D105-116 (EPIM) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.
    2. Make sure that no terminals are worn down and that there are no bad connections.
    3. Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.
    4. Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK OR REPLACE TURBOCHARGER SUB-ASSEMBLY
  1. Disconnect the actuator hose from the compressor housing.

  1. Close the compressor housing side tube with a hose clip or equivalent.

  1. A148172
    Using SST, apply pressure to the actuator to open the waste gate valve.

    Valve opening pressure:
    Specified pressure* (See table below)

    NOTICE:
    Never apply more than the predetermined maximum pressure* to the actuator.

    HINT:
    *: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see the table below.

    Specifications: 
    Turbocharger Sub-assembly
    (Part No.)
    Valve Opening Pressure
    (kPa: Gauge Pressure)
    Maximum Pressure
    (kPa: Gauge Pressure)
    Reference:
    Rod Stroke
    (mm)
    17201-30070
    130
    147.8
    0.89 to 1.74
    17201-30080
    119
    136
    0.98 to 1.91

SST
09992-00242  
  1. Check that the actuator rod moves and that the waste gate valve opens.

HINT:
If the waste gate valve does not open, replace the turbocharger sub-assembly.


NEXT


8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END

9. READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).

    Standard:
    Difference between MAP and Atmosphere Pressure is less than 8 kPa.

    HINT:
    1. If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
    2. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.

    Result 
    Result
    Proceed to
    MAP and Atmosphere Pressure have same value
    A
    MAP is different from actual atmospheric pressure
    B
    Atmosphere Pressure is different from actual atmospheric pressure
    C



B
Go to step 13

C
Go to step 14
A


10. CHECK AIR INTAKE SYSTEM
  1. Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

    HINT:
    1. Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
    2. Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
    3. Using your hand, check whether the pipes and hoses in the intake system are securely connected.
    4. By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
    5. Check for any modifications in the intake system made by the user.

    OK:
    No leakage or blockage.



NG
Go to step 15
OK


11. CHECK TURBOCHARGER SUB-ASSEMBLY

  1. A103067
    Inspect the turbine shaft.
    1. Hold the nut of the turbine shaft with your fingers and check that the vertical, horizontal and axial play of the turbine shaft is not large.

    2. Rotate the turbine shaft with your fingers and check that it rotates smoothly.

  1. Inspect the turbocharger housing.

    1. Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.

    2. Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



NG
Go to step 16
OK


12. CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NEXT
Go to step 17
13. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor.



NEXT
Go to step 17
14. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 17
15. REPAIR OR REPLACE AIR INTAKE SYSTEM
  1. Repair or replace the malfunctioning part in the air intake system.



NEXT
Go to step 17
16. REPLACE TURBOCHARGER SUB-ASSEMBLY
  1. Replace the turbocharger sub-assembly (Click here).


NEXT


17. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END

18. INSPECT CLOGGED FUEL PIPE
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail.

  1. With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.

  1. Check the Target Common Rail Pressure and Common Rail Pressure value.A261221E05

    Result 
    Result
    Proceed to
    While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1
    B
    "Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
    Except above
    A

    NOTICE:
    1. *1: The cause may be a squashed or blocked fuel pipe or hose.
    2. *2: The cause may be a clogged fuel filter.



B
Go to step 20
A


19. REPLACE SUCTION CONTROL VALVE
  1. Replace the suction control valve (Click here).



NEXT
Go to step 21
20. REPAIR OR REPLACE CLOGGED FUEL LINE
  1. Repair or replace the clogged (including frozen fuel) fuel pipe.

  1. Replace the fuel filter element sub-assembly.

    HINT:
    If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.


NEXT


21. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


22. PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


23. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

  1. Take a snapshot with the GTS during the Active Test.

  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

    A227749E05

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.

    HINT:
    1. "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
    2. "Common Rail Pressure" is the actual fuel pressure.



NG
Go to step 24
OK

END

24. REPLACE COMMON RAIL ASSEMBLY
  1. Replace the common rail assembly (Click here).


NEXT


25. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


26. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.

  1. Take a snapshot with the GTS during the Active Test.

  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

    A227749E05

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.

    HINT:
    1. "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
    2. "Common Rail Pressure" is the actual fuel pressure.


NEXT

END

27. CHECK INTAKE SYSTEM
  1. Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

    HINT:
    1. Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
    2. Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
    3. Using your hand, check whether the pipes and hoses in the intake system are securely connected.
    4. When checking whether the intake system is clogged (which causes a low MAP), perform the following checks:
      1. Check whether the air cleaner is clogged.
      2. Check whether an intake hose is clogged.
      3. Check whether the diesel throttle valve is stuck in the closed position.
    5. Check for any modifications in the intake system made by the user.

OK:
No leaks or blockages in the intake system.



NG
Go to step 31
OK


28. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-2 (PIM) - D105-117 (PIM)
    Always
    Below 1 Ω
    D51-3 (VC) - D105-93 (VCPM)
    Always
    Below 1 Ω
    D51-1 (E) - D105-116 (EPIM)
    Always
    Below 1 Ω
    D51-2 (PIM) or D105-117 (PIM) - Body ground
    Always
    10 kΩ or higher
    D51-3 (VC) or D105-93 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D51-1 (E) or D105-116 (EPIM) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.
    2. Make sure that no terminals are worn down and that there are no bad connections.
    3. Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.
    4. Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


29. REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
  1. Remove the electric EGR control valve assembly.

  1. Visually check the electric EGR control valve assembly for deposits.If there are deposits, clean the electric EGR control valve assembly.

    HINT:
    1. If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
    2. If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.
    3. If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.
    4. When cleaning the electric vacuum regulating valve assembly, use a piece of cloth soaked with nonresidue solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.

  1. Reinstall the electric EGR control valve assembly.


NEXT


30. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Inspect the electric EGR control valve assembly (Click here).



OK
Go to step 32

NG
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
31. REPAIR OR REPLACE AIR INTAKE SYSTEM
  1. Repair or replace the malfunctioning part in the air intake system.


NEXT


32. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


NG
Go to step 33
OK

END

33. CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
  1. Remove the front exhaust pipe assembly.

  1. Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.

    OK:
    Less than 10% of the cells are clogged.

  1. Reinstall the front exhaust pipe assembly.



NG
Go to step 35
OK


34. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Disconnect the actuator hose from the compressor housing.

  1. Close the compressor housing side tube with a hose clip or equivalent.

  1. A148172
    Using SST, apply pressure to the actuator to open the waste gate valve.

    Valve opening pressure:
    Specified pressure* (See table below)

    NOTICE:
    Never apply more than the predetermined maximum pressure* to the actuator.

    HINT:
    *: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see the table below.

    Specifications: 
    Turbocharger Sub-assembly
    (Part No.)
    Valve Opening Pressure
    (kPa: Gauge Pressure)
    Maximum Pressure
    (kPa: Gauge Pressure)
    Reference:
    Rod Stroke
    (mm)
    17201-30070
    130
    147.8
    0.89 to 1.74
    17201-30080
    119
    136
    0.98 to 1.91

SST
09992-00242  
  1. Check that the actuator rod moves and that the waste gate valve opens.

HINT:
If the waste gate valve does not open, replace the turbocharger sub-assembly.

  1. A103067
    Inspect the turbine shaft.
    1. Hold the nut of the turbine shaft with your fingers and check that the vertical, horizontal and axial play of the turbine shaft is not large.

    2. Rotate the turbine shaft with your fingers and check that it rotates smoothly.

  1. Inspect the turbocharger housing.

    1. Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.

    2. Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



OK
Go to step 37

NG
Go to step 36
35. REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
  1. Replace the front exhaust pipe assembly.



NEXT
Go to step 38
36. REPLACE TURBOCHARGER SUB-ASSEMBLY
  1. Replace the turbocharger sub-assembly (Click here).



NEXT
Go to step 38
37. CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).


NEXT


38. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


NG
Go to step 39
OK

END

39. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
  1. Clean the fuel filter case and replace the fuel filter.

    HINT:
    Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.


NEXT


40. REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
  1. Replace the injector assemblies (Click here).

NOTICE:
  1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
  2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
  3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
  4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
  5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.


NEXT


41. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


42. PERFORM ECM INITIALIZATION AND REGISTER COMPENSATION CODE

  1. A082779E90
    Perform the ECM initialization.
    1. Connect terminals 13 (TC) and 4 (CG) of the DLC3.

    2. Turn the ignition switch to ON for 50 minutes or more.

      NOTICE:
      1. Perform ECM initialization only when the injectors for all the cylinders have been replaced.
      2. It is necessary to wait for 50 minutes or more. Otherwise, ECM initialization is not completed.

    3. Turn the ignition switch off.

    4. Disconnect terminals 13 (TC) and 4 (CG).

  1. Register the injector compensation codes (Click here).


NEXT


43. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END

44. COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE
  1. Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the GTS.

    HINT:
    Confirm the state of the following conditions when the lack of power was experienced.

    1. Accelerator pedal position (vehicle load)
    2. Vehicle speed
    3. Engine coolant temperature
    4. Ambient temperature
    5. Driving conditions before the lack of power occurred
    6. Climate
    7. Road and traffic conditions
    8. When (what day) the problem was noticed
    9. Whether the problem occurs suddenly or gradually
    10. How often the problem occurs
    11. Why the customer felt there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power, etc.)
    12. Level of lack of power (slight or drastic)
    Result 
    Result
    Proceed to
    Significant difference is not found
    A
    Significant difference is found
    B



B
Go to step 4
A


45. EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER
  1. Vehicle performance is normal.There is no problem at this point in time. However, if the problem recurs, ask the customer to explain in detail the situation in which the problem occurred.The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.


NEXT

END


← Lack of Power or Hesitation (Apr 2016 – Dec 2016)Turbocharger Oil Leak and White Smoke (Oct 2014 – Dec 2014) →