DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed /
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
-
Engine Speed
Engine speed /
Min.: 0 rpm
Max.: 16383.75 rpm
600 to 700 rpm: Idling
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
- If value -40°C (-40°F): sensor circuit open
- If value 140°C (284°F): sensor circuit shorted
Battery Voltage
Battery voltage/
Min.: 0 V
Max.: 65.535 V
11 to 14 V: Ignition switch ON
-
Accelerator Position
Accelerator pedal position/
Min.: 0%
Max.: 399.9%
Actual accelerator pedal position
-
N Range Status
Shift lever N status/
ON or OFF
- ON: Shift lever in P or N
- OFF: Shift lever not in P or N
-
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in P or N
- OFF: Shift lever not in P or N
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Stop Light Switch
Stop light switch status/
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
- Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed
- Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed)
-
Shift SW Status (P Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in P
- OFF: Shift lever not in P
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in R
- OFF: Shift lever not in R
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (N Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in N
- OFF: Shift lever not in N
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (N, P Range) Supported
Status of park/neutral position switch (N or P) supported/
Supp or Unsupp
-
-
Shift SW Status (N, P Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in P or N
- OFF: Shift lever not in P or N
-
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not held in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not held in "-" (down-shift)
-
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
- ON: Shift lever in S, "+" or "-"
- OFF: Shift lever not in S, "+" or "-"
-
Shift SW Status (D Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in D, S, "+" or "-"
- OFF: Shift lever not in D, S, "+" or "-"
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
- Approx. 80°C (176°F): After stall test
- Equal to ambient temperature when cold soak
If the value -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
- Approx. 80°C (176°F): After stall test
- Equal to ambient temperature when cold soak
If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate
Estimated value of ATF thermal degradation/
Min.: 0
Max.: 65535
-
Data List value is invalid for vehicles equipped with the 2TR-FE engine and AC60E A/T.
NT Sensor Voltage
Transmission revolution sensor NT output voltage/
Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling
-
SP2 Sensor Voltage
Transmission revolution sensor SP2 output voltage/
Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling
-
Lock Up
Lock up/
ON or OFF
- ON: Lock-up operating
- OFF: Lock-up not operating
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Same as actual gear
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- ON: Shift solenoid valve SLT operating
- OFF: Shift solenoid valve SLT not operating
-
SLU Solenoid Status
Shift Solenoid SLU Status/
ON or OFF
- ON: Shift solenoid valve SLU operating
- OFF: Shift solenoid valve SLU not operating
-
SL Solenoid Status
Shift Solenoid SL Status/
ON or OFF
- ON: Shift solenoid valve SL operating
- OFF: Shift solenoid valve SL not operating
-
Torque Converter Temperature Raise History
Torque converter temperature raise history status/
ON or OFF
OFF
-
- If value -40°C (-40°F): sensor circuit open
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
*: The "Activate the Solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Connects and disconnects TC and TE1.
(changes to the fluid temperature detection mode)
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Vehicle stopped
Activate the Solenoid (SLU)
Operates shift solenoid valve SLU
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
Activate the Solenoid (SLT)*
Operates shift solenoid valve SLT to raise the line pressure.
ON/OFF - HINT:
- ON: No action (normal operation)
- OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).
[Vehicle Condition] - Vehicle Stopped
- Engine idling
Activate the Lock Up
Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition.
ON/OFF
Can be used to check shift solenoid valves SLU and SL operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 30%
- Vehicle speed: 80 km/h (50 mph) or more
Activate the Solenoid (SL)
Operates shift solenoid valve SL
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
Control the Shift Position
Operates the shift solenoid valves to allow gears to be selected manually.
- Press "→" button: Up-shift occurs
- Press "←" button: Down-shift occurs
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 seconds interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]- 50 km/h (31 mph) or less
Activate the Solenoid (SL1)
Operates shift solenoid valve SL1
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL2)
Operates shift solenoid valve SL2
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL3)
Operates shift solenoid valve SL3
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL4)
Operates shift solenoid valve SL4
ON/OFF
[Vehicle Condition] - Ignition switch ON
- Engine stopped
- Shift lever in P or N
- HINT:
- Note that the pressure readings for the Active Test and Hydraulic Test are different.
- Ignition switch ON