2014-2019 Hiace · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
  1. One of the following conditions is met.
    1. P input signal is ON
    2. N input signal is ON
    3. NSW input signal is ON
  2. R input signal
  3. D input signal
(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2 trip detection logic):
  1. P input signal
  2. N input signal
  3. NSW input signal
  4. R input signal
(C) All signals are OFF simultaneously for NSW, P, R, N and D (2 trip detection logic).
  1. Open or short in park/neutral position switch assembly circuit
  2. Transmission control switch (shift lock control unit assembly)
  3. Park/neutral position switch assembly
  4. ECM

MONITOR DESCRIPTION

This DTC indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C321084E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
    Shift SW Status (P Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
    Shift SW Status (R Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
    Shift SW Status (N Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    1. ON: Shift lever in S, "+" or "-"
    2. OFF: Shift lever not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in D, S, "+" or "-"
    2. OFF: Shift lever not in D, S, "+" or "-"
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.


1. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

  1. C321062E01
    Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D37-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    D37-2 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

  1. C321062E02
    Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D37-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    D37-4 (B) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
Go to step 7
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C197712E56
    Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in P or N
    Below 1 Ω
    2 (RB) - 6 (PL)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    2 (RB) - 9 (NL)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D, S, "+" or "-"
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever not in P or N
    10 kΩ or higher
    2 (RB) - 6 (PL)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    2 (RB) - 9 (NL)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D, S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

  1. C199171E36
    Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H72-6 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    H72-6 (IG) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

  1. C199170E20
    Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (IG) - 13 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    6 (IG) - 13 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

  1. C319064E01
    Disconnect the ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D116-70 (P) - Body ground
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    D116-65 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    D116-39 (N) - Body ground
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    D116-66 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D, S, "+" or "-"
    11 to 14 V
    B94-59 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    D116-70 (P) - Body ground
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    D116-65 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    D116-39 (N) - Body ground
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    D116-66 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D, S, "+" or "-"
    Below 1 V
    B94-59 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    HINT:
    *: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the D37 park/neutral position switch assembly connector.

  1. Disconnect the B94 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-4 (B) - B94-23 (NSW)
    Always
    Below 1 Ω
    D37-4 (B) - Body ground
    Always
    10 kΩ or higher
    B94-23 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Apr 2016 – Dec 2016)P0711 Transmission Fluid Temperature Sensor "A" Performance (Jan 2015 – Mar 2016) →