2014-2019 Hiace · Service Manual TRANSMISSION

P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The No. 1 ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM.
The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.
The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.
DTC No.
DTC Detection Condition
Trouble Area
P0712
No. 1 ATF temperature sensor resistance is below 79 Ω for 0.5 seconds or more (1 trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. ECM
P0713
No. 1 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more and either condition is met (1 trip detection logic):
(A) 15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).
  1. Open in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. ECM

MONITOR DESCRIPTION

The No. 1 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the No. 1 ATF temperature sensor circuit. If the resistance value of the No. 1 ATF temperature sensor is below 79 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the No. 1 ATF temperature sensor or wiring. The ECM will illuminate the MIL and store the DTC.
*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on the GTS display.


WIRING DIAGRAM

C319068E01

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    1. Approx. 80°C (176°F): After stall test
    2. Equal to ambient temperature when cold soak
    If the value -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P0712 is output and the GTS indicates 150°C (302°F) or higher, there is a short circuit.
    When DTC P0713 is output and the GTS indicates -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the GTS in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit

    HINT:
    If the circuit related to the No. 1 ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored.
    It is not necessary to inspect the circuit when P0711 is stored.


1. INSPECT NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

  1. C319326E01
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (OT+) - 4 (OT-)
    Always
    79 Ω to 156 kΩ
    3 (OT+) - Body ground
    Always
    10 kΩ or higher
    4 (OT-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C267934E02
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D116-127 (THO1) - D116-128 (ETHO)
    Always
    79 Ω to 156 kΩ
    D116-127 (THO1) - Body ground
    Always
    10 kΩ or higher
    D116-128 (ETHO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713) (Jan 2015 – Mar 2016)P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713) (from Jan 2017) →