2014-2019 Hiace · Service Manual TRANSMISSION

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

The amount of current flow to the shift solenoid valve SLU is controlled by the TCM. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.
C294519E01
DTC Code
DTC Detection Condition
Trouble Area
P2759
Open or short is detected in the shift solenoid valve SLU circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. TCM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the TCM determines that there is a malfunction. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C294509E07

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

  1. C214964E05
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (SLU+) - 7 (SLU-)
    20°C (68°F)
    5.1 to 5.5 Ω
    3 (SLU+) - Body ground
    Always
    10 kΩ or higher
    7 (SLU-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. C371285E04
    Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-21 (SLU+) - O1-22 (SLU-)
    20°C (68°F)
    5.1 to 5.5 Ω
    O1-21 (SLU+) - Body ground
    Always
    10 kΩ or higher
    O1-22 (SLU-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE SLU
C209928E15
  1. Remove shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.1 to 5.5 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Solenoid Valve SLU)



NG
REPLACE SHIFT SOLENOID VALVE SLU
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P2740 Transmission Fluid Temperature Sensor "B" Circuit (+ P2742, P2743) (from Jan 2017)P2769/64 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (+ P2770/64) (from Oct 2014) →