2014-2019 Hiace · Service Manual TRANSMISSION

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve S

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

DESCRIPTION

Refer to the system description for DTC P2757 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2759
Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip detection logic).
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. ECM

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit is detected, the ECM determines there is a malfunction. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C251557E16

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

  1. C319326E08
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    21 (SLU+) - 22 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    21 (SLU+) - Body ground
    Always
    10 kΩ or higher
    22 (SLU-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C267934E08
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D116-13 (SLU+) - D116-12 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    D116-13 (SLU+) - Body ground
    Always
    10 kΩ or higher
    D116-12 (SLU-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SLU

  1. C197715E25
    Remove shift solenoid valve SLU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Shift Solenoid Valve SLU


NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)


← P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (Apr 2016 – Dec 2016)P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (from Dec 2017) →