2014-2019 Hiace · Service Manual TRANSMISSION

P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0748
An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL1 circuit while driving and shifting gears (SL1 output signal duty is more than 0% and less than 100% under normal conditions) (1 trip detection logic).
  1. Open or short in shift solenoid valve SL1 circuit
  2. Shift solenoid valve SL1
  3. ECM

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the ECM detects the problem and illuminates the MIL and stores the DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)
While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines there is a malfunction (Click here).

WIRING DIAGRAM

C311453E83

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).

HINT:
  1. The following table shows normal operation of the shift solenoid valve SL1 when the shift lever is in D:
    ECM commanded gear
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid valve SL1
    ON
    ON
    ON
    ON
    OFF
    OFF
  2. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Perform the D Position Shift Test in Road Test (Click here).
    2. Check for DTCs again (Click here).


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)

  1. C319326E03
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    25 (SL1+) - 26 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    25 (SL1+) - Body ground
    Always
    10 kΩ or higher
    26 (SL1-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C267934E43
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D134-5 (SL1+) - D134-35 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    D134-5 (SL1+) - Body ground
    Always
    10 kΩ or higher
    D134-35 (SL1-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SL1

  1. C197715E25
    Remove shift solenoid valve SL1 (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Shift Solenoid Valve SL1


NG
REPLACE SHIFT SOLENOID VALVE SL1 (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)


← P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (from Jan 2017)P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (from Jan 2017) →