2014-2019 Hiace · Service Manual ENGINE

P0340 Camshaft Position Sensor Circuit

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The camshaft position sensor (VV1 signal sensor) for the intake camshaft consists of a magnet and MRE (Magneto-Resistive Element).
The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, are sends it to the ECM. Then the ECM uses this data to control fuel injection time and injection timing.
DTC No.
DTC Detection Condition
Trouble Area
P0340
When one of the following conditions is met:
  1. No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).
  2. No camshaft position sensor signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).
  3. A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
  1. Open or short in camshaft position sensor (for intake side) circuit
  2. Camshaft position sensor (for intake side)
  3. Intake camshaft
  4. Timing chain jumped tooth
  5. ECM
P0342
The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor (for intake side) circuit
  2. Camshaft position sensor (for intake side)
  3. ECM
P0343
The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor (for intake side) circuit
  2. Camshaft position sensor (for intake side)
  3. ECM
Reference: Inspection using an oscilloscope.
A255508E20
  1. The correct waveform is as shown.
  2. VV1 stands for the camshaft position sensor (for intake side) signal and EV1 stands for the camshaft position sensor (for exhaust side) signal.
Terminal No. (Symbol)
Tool Setting
Condition
D116-82 (VV1+) - D116-115 (VV1-)
5 V/DIV, 20 ms/DIV
Idling
D116-80 (EV1+) - D116-112 (EV1-)
5 V/DIV, 20 ms/DIV
Idling

MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the camshaft revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main)
Camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340, P0342 or P0343.
  12. Check the DTC judgment result.
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.


WIRING DIAGRAM

A240394E08

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)

  1. A208648E39
    Disconnect the camshaft position sensor (for intake side) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D110-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor (for Intake Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor (for intake side) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D110-1 (VVI+) - D116-82 (VV1+)
    Always
    Below 1 Ω
    D110-2 (VVI-) - D116-115 (VV1-)
    Always
    Below 1 Ω
    D110-1 (VVI+) or D116-82 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D110-2 (VVI-) or D116-115 (VV1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

  1. BR03795E17
    Check the camshaft position sensor (for intake side).

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH)
  1. Check the teeth of the camshaft timing gear assembly.

    OK:
    Teeth do not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


5. REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (for intake side) (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine and idle it for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0340, P0342 or P0343 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Jan 2017)P0340 Camshaft Position Sensor Circuit (+ P0342, P0343) (Apr 2016 – Dec 2016) →