2014-2019 Hiace · Service Manual BRAKE

FREEZE FRAME DATA

Troubleshooting · Vehicles built Jan 2015 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


FREEZE FRAME DATA
  1. Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.


CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES
  1. Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.

  2. Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.

  3. The number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the system was activated can be stored and displayed.

    HINT:
    1. After turning the ignition switch from off to ON, if the vehicle is not driven (vehicle speed below 7 km/h (4.3 mph)), the value does not increase.
    2. The value "31" is displayed when the ignition switch was turned to ON more than 31 times.

  4. Check freeze frame data when the system operates

    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3 and turn the ignition switch to ON.

    3. Enter the following menus: Chassis / ABS/VSC/TRC / Utility.

    4. Select "ABS History".

    5. Check the freeze frame data when the system operates.


CHECK FREEZE FRAME DATA WHEN DTC WAS STORED
  1. Freeze frame data is stored when a DTC is output.

  2. Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.

  3. The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.

    HINT:
    The value "31" is displayed when the ignition switch was turned to ON more than 31 times.

  4. Check freeze frame data when DTC is output

    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3 and turn the ignition switch to ON.

    3. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

    4. Select a DTC to display the freeze frame data.

    5. Check the freeze frame data for the output DTC.

      ABS/VSC/TRC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FR Speed Open
      Front speed sensor RH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      FL Speed Open
      Front speed sensor LH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RR Speed Open
      Rear speed sensor RH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RL Speed Open
      Rear speed sensor LH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      IG Voltage Value Decreased
      IG voltage value decrease detection / Error or Normal
      Normal
      Error: Momentary interruption
      IG Voltage Value Increased
      IG voltage value increase detection / Error or Normal
      Normal
      Error: Momentary interruption
      FR Speed Sensor Voltage Open
      Front speed sensor RH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      FL Speed Sensor Voltage Open
      Front speed sensor LH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RR Speed Sensor Voltage Open
      Rear speed sensor RH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RL Speed Sensor Voltage Open
      Rear speed sensor LH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      Elapsed Time after Freeze Trigger
      Elapsed time after freeze trigger / Min.: 0 msec, Max.: 500 msec
      -
      -
      Number of IG ON
      Number of operations of ignition switch being turned to ON after storing freeze frame data / 0 to 31
      -
      -
      Stop Light SW
      Stop light switch assembly / ON or OFF
      ON: Brake pedal depressed
      OFF: Brake pedal released
      -
      Parking Brake SW
      Parking brake switch assembly / ON or OFF
      ON: Parking brake applied
      OFF: Parking brake released
      -
      Operated System
      Operated system status / Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys
      Actual operated system
      Non: No operation activated
      ABS: ABS activated
      VSC: VSC activated*
      TRC: TRC activated*
      BA: BA activated*
      Fail: Fail safe mode activated*
      PBA: PBA activated*
      PB: PB activated*
      HA-CTRL: Hill-start assist control activated*
      TSC: Trailer sway control activated*
      Sys: System prohibit activated
      1. *: Not supported
      FR Wheel Speed
      Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      FL Wheel Speed
      Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RR Wheel Speed
      Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RL Wheel Speed
      Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Vehicle Speed
      Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Vehicle Speed Grade
      Vehicle acceleration / Min.: -25.10 m/s2, Max.: 24.90 m/s2
      Vehicle stopped: 0 m/s2
      During driving: Changes in proportion with vehicle acceleration/deceleration


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTC will also clear the freeze frame data.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Clear the DTC and freeze frame data (Click here).

← FREEZE FRAME DATA (Oct 2014 – Dec 2014)FREEZE FRAME DATA (from Jan 2017) →