FREEZE FRAME DATA
Troubleshooting · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
| FREEZE FRAME DATA |
Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
| CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES |
Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.
Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.
The number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the system was activated can be stored and displayed.
- HINT:
- After turning the ignition switch from off to ON, if the vehicle is not driven (vehicle speed below 7 km/h (4.3 mph)), the value does not increase.
- The value "31" is displayed when the ignition switch was turned to ON more than 31 times.
- After turning the ignition switch from off to ON, if the vehicle is not driven (vehicle speed below 7 km/h (4.3 mph)), the value does not increase.
Check freeze frame data when the system operates
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility.
Select "ABS History".
Check the freeze frame data when the system operates.
| CHECK FREEZE FRAME DATA WHEN DTC WAS STORED |
Freeze frame data is stored when a DTC is output.
Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.
- HINT:
- The value "31" is displayed when the ignition switch was turned to ON more than 31 times.
Check freeze frame data when DTC is output
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
Front speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Open
Front speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
IG Voltage Value Decreased
IG voltage value decrease detection / Error or Normal
Normal
Error: Momentary interruption
IG Voltage Value Increased
IG voltage value increase detection / Error or Normal
Normal
Error: Momentary interruption
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
Elapsed Time after Freeze Trigger
Elapsed time after freeze trigger / Min.: 0 msec, Max.: 500 msec
-
-
Number of IG ON
Number of operations of ignition switch being turned to ON after storing freeze frame data / 0 to 31
-
-
Stop Light SW
Stop light switch assembly / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch assembly / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Operated System
Operated system status / Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys
Actual operated system
Non: No operation activated
ABS: ABS activated
VSC: VSC activated*
TRC: TRC activated*
BA: BA activated*
Fail: Fail safe mode activated*
PBA: PBA activated*
PB: PB activated*
HA-CTRL: Hill-start assist control activated*
TSC: Trailer sway control activated*
Sys: System prohibit activated- *: Not supported
FR Wheel Speed
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FL Wheel Speed
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RR Wheel Speed
Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RL Wheel Speed
Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Vehicle Speed
Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Vehicle Speed Grade
Vehicle acceleration / Min.: -25.10 m/s2, Max.: 24.90 m/s2
Vehicle stopped: 0 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
- *: Not supported
| CLEAR FREEZE FRAME DATA |
- NOTICE:
- Clearing the DTC will also clear the freeze frame data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Clear the DTC and freeze frame data (Click here).