2014-2019 Hiace · Service Manual ENGINE

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built from Oct 2014

Also covers:

DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
A210600E03
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM
  3. No. 1 to No. 4 ignition coil assembly
  4. ECM
  1. Reference: Inspection using an oscilloscope.

  2. A093278E05
    Items
    Contents
    Terminals
    1. IGT1, IGT2, IGT3, IGT4 - E1
    2. IGF1 - E1
    Equipment Settings
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.


MONITOR DESCRIPTION

A212405E08
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

WIRING DIAGRAM

A318861E01
A318859E02

INSPECTION PROCEDURE

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is stored, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is stored, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is stored, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is stored, check the No. 4 ignition coil circuit.
  6. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0351, P0352, P0353 or P0354 is output
    A
    DTC P0351, P0352, P0353 and P0354 are output
    B



B
Go to step 6
A


2. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check the DTCs output to the tester.

    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil assembly DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY
A


3. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)

  1. A200905E30
    Disconnect the ignition coil assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D20-1 (+B) - D20-4 (GND)
    Ignition switch ON
    11 to 14 V
    D21-1 (+B) - D21-4 (GND)
    Ignition switch ON
    11 to 14 V
    D22-1 (+B) - D22-4 (GND)
    Ignition switch ON
    11 to 14 V
    D23-1 (+B) - D23-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)



NG
Go to step 6
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D20-2 (IGF) - D97-82 (IGF1)
    Always
    Below 1 Ω
    D21-2 (IGF) - D97-82 (IGF1)
    Always
    Below 1 Ω
    D22-2 (IGF) - D97-82 (IGF1)
    Always
    Below 1 Ω
    D23-2 (IGF) - D97-82 (IGF1)
    Always
    Below 1 Ω
    D20-2 (IGF) or D97-82 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D21-2 (IGF) or D97-82 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D22-2 (IGF) or D97-82 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D23-2 (IGF) or D97-82 (IGF1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK


5. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D20-3 (IGT1) - D97-109 (IGT1)
    Always
    Below 1 Ω
    D21-3 (IGT2) - D97-108 (IGT2)
    Always
    Below 1 Ω
    D22-3 (IGT3) - D97-107 (IGT3)
    Always
    Below 1 Ω
    D23-3 (IGT4) - D97-106 (IGT4)
    Always
    Below 1 Ω
    D20-3 (IGT1) or D97-109 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D21-3 (IGT2) or D97-108 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D22-3 (IGT3) or D97-107 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D23-3 (IGT4) or D97-106 (IGT4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)

6. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D20-4 (GND) - Body ground
    Always
    Below 1 Ω
    D21-4 (GND) - Body ground
    Always
    Below 1 Ω
    D22-4 (GND) - Body ground
    Always
    Below 1 Ω
    D23-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
OK


7. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the ignition coil assembly connectors.

  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D20-1 (+B) - 10B-4
    Always
    Below 1 Ω
    D21-1 (+B) - 10B-4
    Always
    Below 1 Ω
    D22-1 (+B) - 10B-4
    Always
    Below 1 Ω
    D23-1 (+B) - 10B-4
    Always
    Below 1 Ω
    D20-1 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher
    D21-1 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher
    D22-1 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher
    D23-1 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT NO. 1 INTEGRATION RELAY (INJ)
  1. Inspect the No. 1 integration relay (INJ) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


9. CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
A321249E01
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    10B-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
OK


10. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    10B-3 - Body ground
    Always
    Below 1 Ω
    Result 
    Result
    Proceed to
    OK (w/ Air Pressure Sensor)
    A
    OK (w/o Air Pressure Sensor)
    B
    NG
    C



B
Go to step 12

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


11. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    10A-8 - 10B-2
    Always
    Below 1 Ω
    10A-8 or 10B-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

12. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 2 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Remove the No. 2 integration relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12B-7 - 10B-2
    Always
    Below 1 Ω
    12B-7 or 10B-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← P0340 Camshaft Position Sensor Circuit (+ P0341) (from Jan 2015)P0412 Secondary Air Injection System Switching Valve "A" Circuit (from Oct 2014) →