FREEZE FRAME DATA
Troubleshooting · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| FREEZE FRAME DATA |
Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
| CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES |
Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.
Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.
The number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the system was activated can be stored and displayed.
- HINT:
- When the vehicle is stopped (vehicle speed below 7 km/h (4.3 mph)), turning the ignition switch from off to ON does not cause the value to increase.
- The value "31" is displayed when the ignition switch was turned to ON more than 31 times.
- When the vehicle is stopped (vehicle speed below 7 km/h (4.3 mph)), turning the ignition switch from off to ON does not cause the value to increase.
Check freeze frame data when the system operates
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility.
Select "ABS History".
Check the freeze frame data when the system operates.
| CHECK FREEZE FRAME DATA WHEN DTC WAS STORED |
Freeze frame data is stored when a DTC is output.
Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.
- HINT:
- The value "31" is displayed when the ignition switch was turned to ON more than 31 times.
Check freeze frame data when DTC is output
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
Front speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Open
Front speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
EFI Communication Open
ECM communication open detection / Error or Normal
Normal
Error: Momentary interruption
Yaw Rate Open
Yaw rate sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Deceleration Open
Acceleration sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Steering Open
Steering angle sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Master Cylinder Open
Master cylinder pressure sensor open detection / Error or Normal
Normal
Error: Momentary interruption
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection / Error or Normal
Normal
Error: Momentary interruption
Yaw Rate Sensor Voltage Open
Yaw rate sensor voltage open detection / Error or Normal
Normal
Error: Momentary interruption
EFI Communication Invalid
ECM communication invalid detection / Error or Normal
Normal
Error: Invalid
Number of IG ON
Number of operations of ignition switch being turned to ON after storing Freeze Frame Data / 0 to 31
-
-
Elapsed Time
Time elapsed after ignition switch turned to ON / Min.: 0 sec, Max.: 100661 sec
-
-
Stop Light SW
Stop light switch assembly / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch assembly / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Gear Position
Gear position information / Fail, 1st-7th, "P, N", 8th, R or Not R
Actual gear position
-
Shift Lever Position
Shift lever position information / Fail, 1st-5th, 6th/B, D/M, "P, N" or R
Actual shift lever position
-
Operated System
Operated system status / Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys
Actual operated system
Non: No operation activated
ABS: ABS activated
VSC: VSC activated
TRC: TRC activated
BA: BA activated
Fail: Fail safe mode activated
PBA: PBA activated*
PB: PB activated*
HA-CTRL: Hill-start assist control activated
TSC: Trailer sway control activated*
Sys: System prohibit activated- *: Not supported
M/C Sensor Grade
Master cylinder pressure sensor change / Min.: -30 MPa/s, Max.: 225 MPa/s
0 MPa/s: When brake pedal is released or pedal held at constant position
When brake pedal is being operated: Changes in proportion with pedal movement speed
Yaw Rate Sensor
Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
0°/s: Vehicle stopped
-128 to 0°/s: Turning right
0 to 127°/s: Turning left
-
Lateral G
Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
During turning: Changes in proportion with acceleration
Forward and Rearward G
Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FL Wheel Speed
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RR Wheel Speed
Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RL Wheel Speed
Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Vehicle Speed
Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Vehicle Speed Grade
Vehicle acceleration / Min.: -25.10 m/s2, Max.: 24.90 m/s2
Vehicle stopped: 0 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
Real Engine Torque
Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 127.0%
Accelerator pedal released: 0%
During accelerator pedal operation: Changes in proportion with the pedal movement
BS1 Voltage Value
+BS voltage value / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
FR Target Oil Pressure
Front wheel RH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
Different according to target oil pressure of each wheel
-
FL Target Oil Pressure
Front wheel LH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
Different according to target oil pressure of each wheel
-
RR Target Oil Pressure
Rear wheel RH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
Different according to target oil pressure of each wheel
-
RL Target Oil Pressure
Rear wheel LH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
Different according to target oil pressure of each wheel
-
Inspection Mode
Inspection mode / Other or Inspect
Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor
Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
Turning left: Positive value increases
Turning right: Negative value decreases
-
TRC/VSC Off Mode
TRC/VSC off mode / Normal, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Master Cylinder Pressure
Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
Proportional to pedal force: Pedal operated
0.00 MPa: Pedal released
-
Master Cylinder Sensor Temperature
Master cylinder pressure sensor temperature / Min.: -80°C (-112°F), Max.: 175°C (347°F)
-
-
Vehicle Stop Time from IG ON
Time vehicle stopped after ignition switch turned to ON / Min.: 0 s, Max.: 1275 s
-
-
Travel Distance from IG ON
Driving time after ignition switch turned to ON / Min.: 0 s, Max.: 1275 s
-
-
Engine Revolutions
Engine speed / Min.: 0 rpm, Max.: 25500 rpm
-
-
Motor Power Supply Voltage
Motor power supply voltage / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
Solenoid Power Supply Voltage
Solenoid power supply voltage / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
MT Voltage Value
Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
-
Changes in proportion to battery voltage
Solenoid State for ECU Control
Solenoid (for ECU control) status / ON or OFF
ON: Solenoid relay operating
OFF: Solenoid relay not operating
-
Motor State for ECU Control
Motor (for ECU control) status / ON or OFF
ON: Motor relay operating
OFF: Motor relay not operating
-
Operation History of IG OFF while Vehicle is moving
History of ignition switch turned off when vehicle is in motion / ON or OFF
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
OFF: No history
-
Master Cylinder Pressure Sensor Power Supply Open
Master cylinder pressure sensor power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Solenoid Power Supply Open
Solenoid power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Motor Power Supply Open
Motor power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Stop Switch Open
Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the stop light switch assembly / Error or Normal
Normal
Error: Momentary interruption
IG Switch
Ignition switch ON status / ON or OFF
-
-
Elapsed Time after Freeze Trigger
Elapsed time after storing freeze frame data / Min.: 0 msec, Max.: 1020 msec
-
-
- *: Not supported
| CLEAR FREEZE FRAME DATA |
- NOTICE:
- Clearing the DTC will also clear the Freeze Frame Data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Clear the DTC and Freeze Frame Data (Click here).