2014-2019 Hiace · Service Manual BRAKE

FREEZE FRAME DATA

Troubleshooting · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


FREEZE FRAME DATA
  1. Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.


CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES
  1. Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.

  2. Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.

  3. The number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the system was activated can be stored and displayed.

    HINT:
    1. When the vehicle is stopped (vehicle speed below 7 km/h (4.3 mph)), turning the ignition switch from off to ON does not cause the value to increase.
    2. The value "31" is displayed when the ignition switch was turned to ON more than 31 times.

  4. Check freeze frame data when the system operates

    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3 and turn the ignition switch to ON.

    3. Enter the following menus: Chassis / ABS/VSC/TRC / Utility.

    4. Select "ABS History".

    5. Check the freeze frame data when the system operates.


CHECK FREEZE FRAME DATA WHEN DTC WAS STORED
  1. Freeze frame data is stored when a DTC is output.

  2. Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.

  3. The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.

    HINT:
    The value "31" is displayed when the ignition switch was turned to ON more than 31 times.

  4. Check freeze frame data when DTC is output

    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3 and turn the ignition switch to ON.

    3. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

    4. Select a DTC to display the freeze frame data.

    5. Check the freeze frame data for the output DTC.

      ABS/VSC/TRC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FR Speed Open
      Front speed sensor RH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      FL Speed Open
      Front speed sensor LH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RR Speed Open
      Rear speed sensor RH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RL Speed Open
      Rear speed sensor LH open detection / Error or Normal
      Normal
      Error: Momentary interruption
      EFI Communication Open
      ECM communication open detection / Error or Normal
      Normal
      Error: Momentary interruption
      Yaw Rate Open
      Yaw rate sensor open detection / Error or Normal
      Normal
      Error: Momentary interruption
      Deceleration Open
      Acceleration sensor open detection / Error or Normal
      Normal
      Error: Momentary interruption
      Steering Open
      Steering angle sensor open detection / Error or Normal
      Normal
      Error: Momentary interruption
      Master Cylinder Open
      Master cylinder pressure sensor open detection / Error or Normal
      Normal
      Error: Momentary interruption
      FR Speed Sensor Voltage Open
      Front speed sensor RH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      FL Speed Sensor Voltage Open
      Front speed sensor LH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RR Speed Sensor Voltage Open
      Rear speed sensor RH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      RL Speed Sensor Voltage Open
      Rear speed sensor LH voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      M/C Pressure Sensor Noise
      Master cylinder pressure sensor noise detection / Error or Normal
      Normal
      Error: Momentary interruption
      Yaw Rate Sensor Voltage Open
      Yaw rate sensor voltage open detection / Error or Normal
      Normal
      Error: Momentary interruption
      EFI Communication Invalid
      ECM communication invalid detection / Error or Normal
      Normal
      Error: Invalid
      Number of IG ON
      Number of operations of ignition switch being turned to ON after storing Freeze Frame Data / 0 to 31
      -
      -
      Elapsed Time
      Time elapsed after ignition switch turned to ON / Min.: 0 sec, Max.: 100661 sec
      -
      -
      Stop Light SW
      Stop light switch assembly / ON or OFF
      ON: Brake pedal depressed
      OFF: Brake pedal released
      -
      Parking Brake SW
      Parking brake switch assembly / ON or OFF
      ON: Parking brake applied
      OFF: Parking brake released
      -
      Gear Position
      Gear position information / Fail, 1st-7th, "P, N", 8th, R or Not R
      Actual gear position
      -
      Shift Lever Position
      Shift lever position information / Fail, 1st-5th, 6th/B, D/M, "P, N" or R
      Actual shift lever position
      -
      Operated System
      Operated system status / Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys
      Actual operated system
      Non: No operation activated
      ABS: ABS activated
      VSC: VSC activated
      TRC: TRC activated
      BA: BA activated
      Fail: Fail safe mode activated
      PBA: PBA activated*
      PB: PB activated*
      HA-CTRL: Hill-start assist control activated
      TSC: Trailer sway control activated*
      Sys: System prohibit activated
      1. *: Not supported
      M/C Sensor Grade
      Master cylinder pressure sensor change / Min.: -30 MPa/s, Max.: 225 MPa/s
      0 MPa/s: When brake pedal is released or pedal held at constant position
      When brake pedal is being operated: Changes in proportion with pedal movement speed
      Yaw Rate Sensor
      Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
      0°/s: Vehicle stopped
      -128 to 0°/s: Turning right
      0 to 127°/s: Turning left
      -
      Lateral G
      Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
      -
      During turning: Changes in proportion with acceleration
      Forward and Rearward G
      Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
      -
      During acceleration/deceleration: Changes in proportion with acceleration
      FR Wheel Speed
      Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      FL Wheel Speed
      Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RR Wheel Speed
      Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RL Wheel Speed
      Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Vehicle Speed
      Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Vehicle Speed Grade
      Vehicle acceleration / Min.: -25.10 m/s2, Max.: 24.90 m/s2
      Vehicle stopped: 0 m/s2
      During driving: Changes in proportion with vehicle acceleration/deceleration
      Real Engine Torque
      Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
      -
      -
      Accelerator Opening Angle %
      Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 127.0%
      Accelerator pedal released: 0%
      During accelerator pedal operation: Changes in proportion with the pedal movement
      BS1 Voltage Value
      +BS voltage value / Min.: 0.00 V, Max.: 20.00 V
      Ignition switch ON: 11 to 14 V
      Changes in proportion to battery voltage
      FR Target Oil Pressure
      Front wheel RH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
      Different according to target oil pressure of each wheel
      -
      FL Target Oil Pressure
      Front wheel LH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
      Different according to target oil pressure of each wheel
      -
      RR Target Oil Pressure
      Rear wheel RH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
      Different according to target oil pressure of each wheel
      -
      RL Target Oil Pressure
      Rear wheel LH target oil pressure / Min.: 0.00 MPa, Max.: 20.00 MPa
      Different according to target oil pressure of each wheel
      -
      Inspection Mode
      Inspection mode / Other or Inspect
      Other: Normal mode
      Inspect: Inspection mode
      -
      Steering Angle Sensor
      Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
      Turning left: Positive value increases
      Turning right: Negative value decreases
      -
      TRC/VSC Off Mode
      TRC/VSC off mode / Normal, TRC OFF or VSC OFF
      Normal: Normal mode
      TRC OFF: TRC off mode
      VSC OFF: VSC off mode
      -
      Master Cylinder Pressure
      Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
      Proportional to pedal force: Pedal operated
      0.00 MPa: Pedal released
      -
      Master Cylinder Sensor Temperature
      Master cylinder pressure sensor temperature / Min.: -80°C (-112°F), Max.: 175°C (347°F)
      -
      -
      Vehicle Stop Time from IG ON
      Time vehicle stopped after ignition switch turned to ON / Min.: 0 s, Max.: 1275 s
      -
      -
      Travel Distance from IG ON
      Driving time after ignition switch turned to ON / Min.: 0 s, Max.: 1275 s
      -
      -
      Engine Revolutions
      Engine speed / Min.: 0 rpm, Max.: 25500 rpm
      -
      -
      Motor Power Supply Voltage
      Motor power supply voltage / Min.: 0.00 V, Max.: 20.00 V
      Ignition switch ON: 11 to 14 V
      Changes in proportion to battery voltage
      Solenoid Power Supply Voltage
      Solenoid power supply voltage / Min.: 0.00 V, Max.: 20.00 V
      Ignition switch ON: 11 to 14 V
      Changes in proportion to battery voltage
      MT Voltage Value
      Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
      -
      Changes in proportion to battery voltage
      Solenoid State for ECU Control
      Solenoid (for ECU control) status / ON or OFF
      ON: Solenoid relay operating
      OFF: Solenoid relay not operating
      -
      Motor State for ECU Control
      Motor (for ECU control) status / ON or OFF
      ON: Motor relay operating
      OFF: Motor relay not operating
      -
      Operation History of IG OFF while Vehicle is moving
      History of ignition switch turned off when vehicle is in motion / ON or OFF
      ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
      OFF: No history
      -
      Master Cylinder Pressure Sensor Power Supply Open
      Master cylinder pressure sensor power supply voltage status / Error or Normal
      Normal
      Error: Momentary interruption
      Solenoid Power Supply Open
      Solenoid power supply voltage status / Error or Normal
      Normal
      Error: Momentary interruption
      Motor Power Supply Open
      Motor power supply voltage status / Error or Normal
      Normal
      Error: Momentary interruption
      Stop Switch Open
      Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the stop light switch assembly / Error or Normal
      Normal
      Error: Momentary interruption
      IG Switch
      Ignition switch ON status / ON or OFF
      -
      -
      Elapsed Time after Freeze Trigger
      Elapsed time after storing freeze frame data / Min.: 0 msec, Max.: 1020 msec
      -
      -


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTC will also clear the Freeze Frame Data.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Clear the DTC and Freeze Frame Data (Click here).

← FREEZE FRAME DATA (Jan 2015 – Mar 2016)FREEZE FRAME DATA (Jan 2017 – Nov 2017) →