2014-2019 Hiace · Service Manual ENGINE

TERMINALS OF ECU

System information · Vehicles built from Oct 2014


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
C299851E01
  1. Disconnect the B75 and B76 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    B76-37 (STA) - Body ground
    Input
    R - Body ground
    When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started".
    20°C (68°F)
    93.75 to 136.36 Ω
    -
    B76-16 (STAR) - Body ground
    Input/Output
    B - Body ground
    Outputs voltage to the starter relay
    1. Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 500 rpm or more continues for 500 ms or more.)

    HINT:
    When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.

    Shift lever in any position other than P or N → shift lever in P or N (at 20°C (68°F))
    10 kΩ or higher → 93.75 to 136.36 Ω
    -
    Receives neutral start switch (P, N position detection) signal
    1. Monitors whether the neutral start switch is on (P or N) or off (other than P or N). Applies voltage via a resistor (large) in the certification ECU (smart key ECU assembly). When the neutral start switch is on, due to the starter relay coil resistance (small) using some of the voltage, the voltage at terminal STAR will be low (2.7 V or less), and when the neutral start switch is off, the voltage will be high (9 V or more).
    Perform the following operations except while the engine is cranking:
    1. Shift lever in any position other than P or N → shift lever in P or N(at 20°C (68°F))
    30 kΩ or higher → 93.75 to 136.36 Ω
    Neutral SW/ Clutch SW
    B75-6 (NE) - Body ground
    Input
    V - Body ground
    Engine speed signal
    Always
    10 kΩ or higher
    Engine Condition
    B75-11 (STP1) - Body ground
    Input
    R - Body ground
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    1 V or less → 9 V or higher
    Stop Light Switch1
    B75-1 (+B) - B75-10 (E)
    Input
    L - W-B
    Power source
    Always
    11 to 14 V
    -
    B75-22 (SLP) - B75-10 (E)
    Input
    LG - W-B
    Steering lock position signal
    Always
    10 kΩ or higher
    Steering Unlock Switch
    B75-8 (P) - B75-10 (E)
    Input
    BE - W-B
    P position signal
    Shift lever in P → Shift lever not in P
    40 kΩ or higher → 200 Ω or less
    Shift P Signal
    B75-10 (E) - Body ground
    -
    W-B - Body ground
    GND
    Always
    Below 1 Ω
    -
    B75-16 (SSW2) - Body ground
    Input
    GR - Body ground
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch2
    B75-18 (SSW1) - Body ground
    Input
    Y - Body ground
    SSW1 contact signal
    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch1
    B75-21 (ACCD) - Body ground
    Output
    R - Body ground
    ACC signal
    20°C (68°F)
    286.11 to 461.12 Ω
    ACC Relay Monitor
    B75-20 (IG1D) - Body ground
    Output
    B - Body ground
    IG1 signal
    20°C (68°F)
    286.12 to 461.13 Ω
    IG Relay Monitor (Outside)
    B76-33 (CUTB) - B75-10 (E)
    Input
    W - W-B
    Dark current cut pin*
    Always
    11 to 14 V
    -
    B75-7 (SPD) - Body ground
    Input
    P - Body ground
    Vehicle speed signal
    Always
    30 kΩ or higher
    Vehicle Speed Signal
    1. *: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds that form the detection area stops).

  3. Reconnect the B75 and B76 connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    B76-37 (STA) - B75-10 (E)
    Input
    R - W-B
    When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started".
    With the brake pedal depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off)
    6 V or higher* → 1.5 V or less
    -
    B76-16 (STAR) - B75-10 (E)
    Input/Output
    B - W-B
    Outputs voltage to the starter relay
    1. Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 500 rpm or more continues for 500 ms or more.)

    HINT:
    When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.

    With the brake pedal depressed, the engine switch is pressed and held → After approx. 1 sec. has elapsed, the engine switch is released
    6 V or higher* → 1.5 V or less
    -
    Receives neutral start switch (P, N position detection) signal
    1. Monitors whether the neutral start switch is on (P or N) or off (other than P or N). Applies voltage via a resistor (large) in the certification ECU (smart key ECU assembly). When the neutral start switch is on, due to the starter relay coil resistance (small) using some of the voltage, the voltage at terminal STAR will be low (2.7 V or less), and when the neutral start switch is off, the voltage will be high (9 V or more).
    Perform the following operations except while the engine is cranking:
    1. Shift lever in any position other than P or N → shift lever in P or N
    9 V or higher → 2.7 V or less
    Neutral SW/ Clutch SW
    B75-6 (NE) - B75-10 (E)
    Input
    V - W-B
    Engine speed signal
    Idling (engine warmed up)
    Pulse generation
    (See waveform 1)
    Engine Condition
    B75-11 (STP1) - B75-10 (E)
    Input
    R - W-B
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    1 V or less → 9 V or higher
    Stop Light Switch1
    B75-22 (SLP) - B75-10 (E)
    Input
    LG - W-B
    Steering lock position signal
    Steering wheel locked → Steering wheel unlocked
    11 to 14 V → 1.5 V or less
    Steering Unlock Switch
    B75-17 (SLR+) - B75-10 (E)
    Output
    V - W-B
    Steering lock motor operation command signal
    (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
    When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
    1. The steering is unlocked.
    2. The engine switch is off.
    3. The shift lever is in P.
    Pulse generation
    (See waveform 2)
    -
    B75-8 (P) - B75-10 (E)
    Input
    BE - W-B
    P position signal
    Shift lever in P → Shift lever not in P
    9 V or higher → 2.76 V or less
    Shift P Signal
    B75-16 (SSW2) - B75-10 (E)
    Input
    GR - W-B
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch2
    B75-18 (SSW1) - B75-10 (E)
    Input
    Y - W-B
    SSW1 contact signal
    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch1
    B75-21 (ACCD) - B75-10 (E)
    Output
    R - W-B
    ACC signal
    Engine switch off → Engine switch on (ACC)
    1 V or less → 8.5 V or higher
    ACC Relay Monitor
    B75-20 (IG1D) - B75-10 (E)
    Output
    B - W-B
    IG1 signal
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher
    IG Relay Monitor (Outside)
    B75-7 (SPD) - B75-10 (E)
    Input
    P - W-B
    Vehicle speed signal
    Vehicle being driven at approx. 5 km/h (3 mph)
    Pulse generation
    (See waveform 3)
    Vehicle Speed Signal

    HINT:
    1. *: While the engine is cranking, the battery voltage may drop to approximately 6 V.
    2. The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.
    3. The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:
      1. To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the engine switch on (ACC) or on (IG).
      2. To lock the steering, open a door with the engine switch off and the shift lever in P.

  5. Using an oscilloscope, check the waveform of the ECU.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. C222647E01
      Waveform 1
      Item
      Content
      Tester Connection
      B75-6 (NE) - B75-10 (E)
      Tool Setting
      2 V/DIV., 2 ms./DIV.
      Vehicle Condition
      Idling (engine warmed up)

      HINT:
      The wavelength becomes shorter as the engine speed increases.

    2. C221561E01
      Waveform 2
      Item
      Content
      Tester Connection
      B75-17 (SLR+) - B75-10 (E)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Steering lock motor not operating → Operating → Not operating
      Text in Illustration 
      *a
      Steering Lock Motor not Operating
      *b
      Steering Lock Motor Operating

    3. B220145E01
      Waveform 3
      Item
      Content
      Tester Connection
      B75-7 (SPD) - B75-10 (E)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Vehicle Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)

CHECK ID CODE BOX (IMMOBILISER CODE ECU) (Click here)
← PROBLEM SYMPTOMS TABLE (from Dec 2017)DIAGNOSIS SYSTEM (from Oct 2014) →