C1425 Open in Stop Light Switch Circuit
Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1425 |
When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
| 1. CHECK STOP LIGHT OPERATION |
Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed
On
Brake pedal released
Off
|
|
||||
| OK | |
| 2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch assembly / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.
- OK:
- The GTS displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch to ON.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC C1425 is not output
A
DTC C1425 is output
B
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 4. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Remove the stop light switch assembly (Click here).
Inspect the stop light switch assembly (Click here).
- OK:
- The stop light switch assembly is normal.
|
|
||||
| OK | |
| 5. CHECK TERMINAL VOLTAGE (STP TERMINAL) |
Turn the ignition switch off.

Reinstall the stop light switch assembly (Click here).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B92-35 (STP) - Body ground
Stop light switch assembly on (Brake pedal depressed)
8 to 14 V
B92-35 (STP) - Body ground
Stop light switch assembly off (Brake pedal released)
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
|
|
||||
| OK | |
| 6. RECONFIRM DTC |
Reconnect the B92 skid control ECU (brake actuator assembly) connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC C1425 is not output
A
DTC C1425 is output
B
- HINT:
- If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click here).
|
|
||||
| A | ||
| ||
| 7. CHECK TERMINAL VOLTAGE (STP TERMINAL) |
![]() ![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B92-35 (STP) - Body ground
Stop light switch assembly on (Brake pedal depressed)
8 to 14 V
B92-35 (STP) - Body ground
Stop light switch assembly off (Brake pedal released)
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
|
|
||||
| OK | ||
| ||
