2014-2019 Hiace · Service Manual BRAKE

C1425 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.
The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.
DTC No.
DTC Detection Condition
Trouble Area
C1425
When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more.
  1. Stop light switch assembly
  2. Wire harness or connector
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

C269036E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK STOP LIGHT OPERATION
  1. Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
Go to step 4
OK


2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. In accordance with the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

    OK:
    The GTS displays ON or OFF according to brake pedal operation.



NG
Go to step 7
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C1425 is not output
    A
    DTC C1425 is output
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).

    OK:
    The stop light switch assembly is normal.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


5. CHECK TERMINAL VOLTAGE (STP TERMINAL)

  1. C306843E04
    Turn the ignition switch off.

  1. Reinstall the stop light switch assembly (Click here).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-35 (STP) - Body ground
    Stop light switch assembly on (Brake pedal depressed)
    8 to 14 V
    B92-35 (STP) - Body ground
    Stop light switch assembly off (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


6. RECONFIRM DTC
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C1425 is not output
    A
    DTC C1425 is output
    B

    HINT:
    If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click here).



B
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

7. CHECK TERMINAL VOLTAGE (STP TERMINAL)
C306843E04
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-35 (STP) - Body ground
    Stop light switch assembly on (Brake pedal depressed)
    8 to 14 V
    B92-35 (STP) - Body ground
    Stop light switch assembly off (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (from Dec 2017)C1425 Open in Stop Light Switch Circuit (Apr 2016 – Dec 2016) →