2014-2019 Hiace · Service Manual BRAKE

C1210 Zero Point Calibration of Yaw Rate Sensor Undone

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor. If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.
The DTCs are also output when the calibration has not been completed.
DTC No.
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of yaw rate sensor undone.
  1. Sensor installation
  2. Yaw rate sensor (Airbag sensor assembly)
  3. Skid control ECU (Brake actuator assembly)
C1336
Zero point calibration of acceleration sensor undone.
  1. Sensor installation
  2. Acceleration sensor (Airbag sensor assembly)
  3. Skid control ECU (Brake actuator assembly)

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly) or yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information (Click here).

HINT:
When U0124 and/or U0126 is output along with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 and/or U0126 first (Click here).


1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
  1. Perform zero point calibration of the yaw rate and acceleration sensor (Click here).


NEXT


2. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Using the GTS, perform a Test Mode (signal check) inspection sensor check and check that all Test Mode (signal check) inspection items change from incomplete to complete (Click here).

    OK:
    All Test Mode (signal check) inspection items change from incomplete to complete.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 3
OK

END

3. CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the airbag sensor assembly has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor is not installed in a tilted position.



NG
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY (Click here)
OK


4. READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch off.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Deceleration Sensor2
    Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
    Vehicle stopped: 0°/s
    Turning right: -128 to 0°/s
    Turning left: 0 to 127°/s
    -

  1. Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

    OK:
    The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (Apr 2016 – Dec 2016)C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (from Dec 2017) →