2014-2019 Hiace · Service Manual BRAKE

C1432 Steering Angle Sensor Power Source Voltage Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.
DTC No.
DTC Detection Condition
Trouble Area
C1432
Steering angle sensor power supply malfunction signal is received from steering angle sensor.
  1. ECU-B fuse
  2. ECU-IG NO. 2 fuse
  3. Steering angle sensor (Spiral with sensor cable sub-assembly)
  4. Wire harness or connector

WIRING DIAGRAM

C321578E01

INSPECTION PROCEDURE

NOTICE:
  1. Do not remove the steering angle sensor from the spiral with sensor cable subassembly.
  2. When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click here).
  2. When the speed sensor or the yaw rate sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).


1. CHECK TERMINAL VOLTAGE (POWER SOURCE CIRCUIT)
  1. Turn the ignition switch off.

  1. C266564E05
    Remove the steering wheel and the column cover.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the H92 steering angle sensor (spiral with sensor cable sub-assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H92-5 (BAT) - Body ground
    Always
    11 to 14 V
    H92-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


2. CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

  1. C266564E06
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H92-1 (ESS) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)
OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)


← C142B Motor Power Supply Voltage Circuit (+ C146C, C146D) (from Dec 2017)C1432 Steering Angle Sensor Power Source Voltage Malfunction (Apr 2016 – Dec 2016) →