2014-2019 Hiace · Service Manual BRAKE

U0073 Control Module Communication Bus OFF

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) receives the signals from the ECM, steering angle sensor (spiral with sensor cable sub-assembly), and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
DTC No.
DTC Detection Condition
Trouble Area
U0073
Either of the following is detected:
  1. A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.)
  2. When the +BS terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more.
  3. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.
    1. The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds.
CAN communication system
U0100
When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. ECM
U0124
Either of the following is detected:
  1. When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more.
  2. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.
    1. The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. Acceleration sensor (Airbag sensor assembly)
U0126
Either of the following is detected:
  1. When the +BS terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.
  2. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
    1. The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. Steering angle sensor (Spiral with sensor cable sub-assembly)

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    EFI Communication Open
    ECM communication open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Deceleration Open
    Acceleration sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption

    Result:
    Result
    Proceed to
    There is a constant open circuit
    A
    There are no momentary interruptions
    B
    There are momentary interruptions
    C

    HINT:
    Perform the above inspection before removing the sensor and connector.



B
Go to step 3

C
Go to step 4
A


2. CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
  1. Turn the ignition switch off.

  1. Check if each sensor or ECM connector is securely connected.

    OK:
    Each connector is securely connected.



NG
CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Record the output DTCs (for VSC system and/or CAN communication system) (Click here for VSC system, or Click here for CAN communication system).

    HINT:
    If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for VSC system) after the CAN communication system returns to normal.


    Result:
    Result
    Proceed to
    DTC (relating to CAN communication system) is output
    A
    DTC (relating to VSC system) is output
    B
    DTC is not output
    C



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

CHECK CAN COMMUNICATION SYSTEM (Click here)

4. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM (Click here).

  1. Check that there is no momentary interruption.


NEXT


5. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.

  1. Check that no CAN communication system DTC is output (Click here).

  1. If VSC system DTCs are output, record them (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (relating to VSC system)
    B
    DTC is output (relating to CAN communication system)
    C

    HINT:
    The CAN communication system must be normal when repairing each sensor DTC (for VSC system).



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
CHECK CAN COMMUNICATION SYSTEM (Click here)
A

END


← C146E Open in ABS Solenoid Relay Circuit (+ C146F) (from Dec 2017)U0073 Control Module Communication Bus OFF (+ U0100, U0124, U0126) (Apr 2016 – Dec 2016) →