2014-2019 Hiace · Service Manual SUSPENSION & AXLE

C2174/74 Vehicle Speed Signal Malfunction

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.
DTC C2191/91 is stored only during the signal check.
DTC Code
Detection Condition
Trouble Area
C2174/74
All conditions below are met:
  1. DTC C2121/21, C2122/22, C2123/23, C2124/24 and/or C2125/25 is output
  2. Vehicle speed signal malfunction
  1. Combination meter assembly
  2. Vehicle speed signal circuit
  3. Wire harness or connector
  4. Tire pressure warning ECU and receiver
  5. Tire pressure warning valve and transmitter
C2191/91
Test mode procedure is performed.
  1. Meter / gauge system (speed signal)
  2. Vehicle speed signal circuit
  3. Wire harness or connector
  4. Tire pressure warning ECU and receiver

WIRING DIAGRAM

C370427E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.

HINT:
When the speedometer needle is not moving, first troubleshoot the meter/gauge system (Click here).


1. READ VALUE USING DATA LIST (VEHICLE SPEED)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on combination meter assembly

  1. Check that the values indicated on the GTS and on the combination meter assembly are the same.

    OK:
    Vehicle speed indicated on the GTS indicates the actual speed.



NG
Go to step 3
OK


2. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Perform a driving test.

  1. Check for DTCs (Click here).

    HINT:
    The time required for DTC C2174 to be stored is 20 minutes.

    Result 
    Result
    Proceed to
    DTC C2174 is not output
    A
    DTC C2174 is output
    B



B
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the T38 tire pressure warning ECU and receiver connector.

  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T38-2 (SPD) - H20-6 (+S)
    Always
    Below 1 Ω
    T38-2 (SPD) or H20-6 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B92-14 (SP1) - H20-7 (SI)
    Always
    Below 1 Ω
    B92-14 (SP1) or H20-7 (SI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK DTC OUTPUT
  1. Clear the DTCs.

    1. for 2TR-FE (w/ Secondary Air Injection System): (Click here)
    2. for 2TR-FE (w/o Secondary Air Injection System): (Click here)
    3. for 2KD-FTV: (Click here)

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check for DTCs.

    HINT:
    1. for 2TR-FE (w/ Secondary Air Injection System): (Click here)
    2. for 2TR-FE (w/o Secondary Air Injection System): (Click here)
    3. for 2KD-FTV: (Click here)

    Result 
    Result
    Proceed to
    DTC P0500 is not output
    A
    DTC P0500 is output
    B



B
GO TO METER / GAUGE SYSTEM (Click here)
A


6. REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
  1. Replace the tire pressure warning ECU and receiver (Click here).


NEXT


7. PERFORM REGISTRATION OF TRANSMITTER ID
  1. Perform registration (Click here).


NEXT


8. PERFORM INITIALIZATION
  1. Set the tire pressure to the specified value (Click here).

  1. Perform initialization (Click here).


NEXT


9. CHECK TEST MODE DTC (C2191/91)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

  1. Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

    Result 
    Result
    Proceed to
    DTC C2191 is not cleared
    A
    DTC C2191 is cleared
    B



B
END
A

GO TO DTC C2121/21 TO C212/25 (Click here)


← C2171/71 Transmitter ID not Registered (from Dec 2017)C2174/74 Vehicle Speed Signal Malfunction (+ C2191/91) (from Dec 2017) →