ON-VEHICLE INSPECTION
Inspection · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 from Jan 2015
| PERFORM SPARK TEST |
Check for DTCs (Click here).
- NOTICE:
- If a DTC is present, perform troubleshooting procedures for that DTC.
Check if sparks occur.
Remove the front seat assembly (Click here).
Remove the front door scuff plate RH.
Remove the 5 bolts and engine service hole sub cover.
Remove the ignition coil assembly.
Using a 16 mm plug wrench, remove the spark plug.
Install the spark plug to the ignition coil assembly and connect the ignition coil connector.
Disconnect the 4 injector connectors.
Ground the spark plug.
Visually check that sparks occur while the engine is being cranked.
- NOTICE:
- Be sure to ground the spark plug before checking.
- If the ignition coil assembly has been struck or dropped, replace it.
- Do not crank the engine for more than 2 seconds.
- Be sure to ground the spark plug before checking.
Spark test procedure.
Check that the wire harness side connector of the ignition coil assembly with igniter is securely connected.
- Result:
Result
Proceed to
NG
Connect securely
OK
Go to next step
Perform spark test on each ignition coil assembly with igniter.
- Replace the ignition coil assembly with igniter with a normal one.
- Perform spark test again.
- Result:
Result
Proceed to
OK
Replace ignition coil assembly with igniter
NG
Go to next step
- Replace the ignition coil assembly with igniter with a normal one.
Check the spark plug.
- Result:
Result
Proceed to
NG
Replace spark plug
OK
Go to next step
Check the power supply to ignition coil assembly with igniter.
- Turn the ignition switch to ON.
- Check that there is battery voltage at the ignition coil positive (+) terminal.
- Result:
Result
Proceed to
NG
Check wiring between engine switch and ignition coil assembly with igniter
OK
Go to next step
- Turn the ignition switch to ON.
Check the camshaft position sensor (Click here).
- Result:
Result
Proceed to
NG
Replace camshaft position sensor
OK
Go to next step
Check the crankshaft position sensor (Click here).
- Result:
Result
Proceed to
NG
Replace crankshaft position sensor
OK
Go to next step
Check IGT signal from the ECM.
- Result:
Result
Proceed to
NG
Check ECM
OK
Repair wiring between ignition coil assembly and ECM
Install the ignition coil assembly.
Using a 16 mm plug wrench, install the spark plug.
- Torque:
- 18 N*m{ 183 kgf*cm , 13 ft.*lbf }
Install the ignition coil assembly.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Install the engine service hole sub cover with the 5 bolts.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
Install the front door scuff plate RH.
Install the front seat assembly (Click here).
| CHECK SPARK PLUG |
- NOTICE:
- Do not use a wire brush for cleaning.
- Do not attempt to adjust the electrode gap of a used spark plug.
- Do not use a wire brush for cleaning.
Check the electrode.
Using a megohmmeter, measure the insulation resistance.

- Standard Insulation Resistance:
Tester Connection
Condition
Specified Condition
Spark plug (terminal part) - Body ground
Always
10 MΩ or higher
Text in Illustration *a
Body Ground
- HINT:
- If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method.
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.- Recommended Spark Plug:
Manufacture
Product
DENSO made
FK20HBR11-T
Check the spark plug electrode gap.
- Standard electrode gap:
- 1.0 to 1.1 mm (0.0394 to 0.0433 in.)
- Maximum electrode gap:
- 1.3 mm (0.0512 in.)
Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.- Air pressure:
- 588 kPa (6.0 kgf/cm2, 85.2 psi)
- Duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
