2014-2019 Hiace · Service Manual BRAKE

C1241 Low Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.
The DTC is canceled when the +BS terminal voltage returns to normal.
DTC No.
DTC Detection Condition
Trouble Area
C1241
Either of the following is detected:
  1. When vehicle speed is 3 km/h (2 mph) or more, +BS terminal voltage is continuously below 9.5 V for 10 seconds or more.
  2. When solenoid relay is on, +BS terminal voltage is below 9.5 V and relay contact is off for 0.22 seconds or more.
  3. When +BS terminal voltage is below 9.5 V, power supply voltage of vehicle speed sensor is continuously low for 60 seconds or more.
  4. When fail-safe motor relay is on and +BS terminal voltage is below 9.5 V, fail-safe motor relay overcurrent continues for 0.05 seconds or more.
  1. ABS SOL fuse
  2. Battery
  3. Charging system
  4. Wire harness or connector
  5. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

C268657E03

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V


    HINT:
    Refer to the inspection procedures: 
    Item
    See page
    1KD-FTV
    Click here
    2KD-FTV
    Click here
    1TR-FE
    Click here
    2TR-FE (except Dual VVT-i)
    Click here
    2TR-FE (w/ Dual VVT-i)
    Click here



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY
OK


2. CHECK TERMINAL VOLTAGE (+BS TERMINAL)
  1. Turn the ignition switch off.

  1. C306843E02
    Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-38 (+BS) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


3. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

  1. C306843E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B92-25 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


4. RECONFIRM DTC
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C1241 is not output
    A
    DTC C1241 is output
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1241 Low Power Supply Voltage Malfunction (Apr 2016 – Dec 2016)C1241 Low Power Supply Voltage Malfunction (from Dec 2017) →