2014-2019 Hiace · Service Manual BODY ELECTRICAL

B1500 Fuel Sender Open Detected

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.
DTC Code
DTC Detection Condition
Trouble Area
B1500
Both conditions are met:
  1. IG voltage is 10.5 V or higher.
  2. Fuel sender gauge operation malfunction.
  1. Fuel sender gauge assembly
  2. Front fuel main and return tube sub-assembly
  3. Harness or connector
  4. Combination meter assembly

WIRING DIAGRAM

E289622E01

INSPECTION PROCEDURE

NOTICE:
Be careful of flames.


1. READ VALUE USING GTS (FUEL INPUT)
  1. Use the Data List to check if the fuel input signal is operating properly (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal/Min.: 0, Max. 127.5
    Current fuel level displayed
    Unit: Liters.

    OK:
    Fuel amount value displayed on the GTS is almost the same as needle indication.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

2. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY AND BODY GROUND)
  1. Disconnect the H20 combination meter assembly connector.

  1. Disconnect the h1*1 or h2*2 front fuel main and return tube sub-assembly connector.

    1. *1: Engine Type Diesel
    2. *2: Engine Type Gasoline

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Engine Type Diesel 
    Tester Connection
    Condition
    Specified Condition
    H20-33 (FUEL) - h1-2
    Always
    Below 1 Ω
    H20-34 (E2) - h1-3
    H20-33 (FUEL) or h1-2 - Body ground
    Always
    10 kΩ or higher
    H20-34 (E2) or h1-3 - Body ground
    Engine Type Gasoline 
    Tester Connection
    Condition
    Specified Condition
    H20-33 (FUEL) - h1-2
    Always
    Below 1 Ω
    H20-34 (E2) - h1-3
    H20-33 (FUEL) or h1-2 - Body ground
    Always
    10 kΩ or higher
    H20-34 (E2) or h1-3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

  1. E158805E11
    Remove the front fuel main and return tube sub-assembly.
    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here
    3. for 5L-E: Click here
    4. for 1TR-FE: Click here
    5. for 2TR-FE: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-2
    Always
    Below 1 Ω
    A-3 - B-1

    1. *: Replacement procedure;
      1. for 1KD-FTV: Click here
      2. for 2KD-FTV: Click here
      3. for 5L-E: Click here
      4. for 1TR-FE: Click here
      5. for 2TR-FE: Click here



NG
REPLACE FRONT FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY*
OK


4. INSPECT FUEL SENDER GAGE ASSEMBLY

  1. E293045E01
    Remove the fuel sender gauge assembly.
    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here
    3. for 5L-E: Click here
    4. for 1TR-FE: Click here
    5. for 2TR-FE: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    Float level is E (lower)
    405.5 to 414.5 Ω

    Text in Illustration  
    *a
    F (Upper)
    *b
    E (Lower)

    HINT:
    *: Replacement procedure;
    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here
    3. for 5L-E: Click here
    4. for 1TR-FE: Click here
    5. for 2TR-FE: Click here



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY*
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← ON-VEHICLE INSPECTION (from Jan 2017)B1500 Fuel Sender Open Detected (Jan 2015 – Dec 2016) →