2014-2019 Hiace · Service Manual BODY

Slide Door Closer Motor RH Circuit

Circuit diagnosis · Vehicles built from Oct 2014

DESCRIPTION

w/o Power Slide Door
  1. The slide door closer relay RH controls the power slide door lock assembly RH. In response to the output signals from the switches in the power slide door lock assembly RH, the slide door closer drives the closer motor.
w/ Power Slide Door
  1. The door control relay assembly controls the power slide door lock assembly RH. In response to the output signals from the switches in the power slide door lock assembly RH, the slide door closer drives the closer motor.

WIRING DIAGRAM


w/ Power Slide Door
B369738E02

w/o Power Slide Door
B367067E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result 
    Result
    Proceed to
    w/o Power Slide Door
    A
    w/ Power Slide Door
    B



B
Go to step 3
A


2. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH
  1. Check the motor.

    1. Remove the power slide door lock assembly RH (Click here).

    2. Inspect the power slide door lock assembly RH (Click here).

  1. Check the switches.

    1. Remove the power slide door lock assembly RH (Click here).

    2. Inspect the power slide door lock assembly RH (Click here).

Result 
Result
Proceed to
OK
A
NG (malfunctioning in motor)
B
NG (malfunctioning in switches)
C


B
REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH (Click here)

C
REPLACE DOOR LOCK SWITCH RH
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH
  1. Check the motor.

    1. Remove the power slide door lock assembly RH (Click here).

    2. Inspect the power slide door lock assembly RH (Click here).

  1. Check the switches.

    1. Remove the power slide door lock assembly RH (Click here).

    2. Inspect the power slide door lock assembly RH (Click here).

Result 
Result
Proceed to
OK
A
NG (malfunctioning in motor)
B
NG (malfunctioning in switches)
C


B
REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH (Click here)

C
REPLACE DOOR LOCK SWITCH RH
A


4. INSPECT REAR DOOR WIRE RH

  1. B365974E01
    Disconnect the ci1 and fc1 rear door wire RH connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-4 - B-18
    Always
    Below 1 Ω
    A-5 - B-12
    Always
    Below 1 Ω
    A-7 - B-8
    Always
    Below 1 Ω
    A-10 - B-16
    Always
    Below 1 Ω
    A-11 - B-15
    Always
    Below 1 Ω
    A-16 - B-14
    Always
    Below 1 Ω
    A-17 - B-9
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear Door Wire RH
    (Door Control Relay Assembly Side)
    *b
    Rear Door Wire RH
    (Power Slide Door Lock Assembly RH Side)



NG
REPLACE REAR DOOR WIRE RH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - POWER SLIDE DOOR LOCK ASSEMBLY RH)
  1. Disconnect the I3 and I4 door control relay assembly connectors.

  1. Disconnect the f1 power slide door lock assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-1 (DC-) - f1-1 (ACT-)
    Always
    Below 1 Ω
    I4-5 (DC+) - f1-2 (ACT+)
    Always
    Below 1 Ω
    I3-4 (HAF) - f1-3 (HAF)
    Always
    Below 1 Ω
    I3-5 (FUL) - f1-4 (FUL)
    Always
    Below 1 Ω
    I3-18 (POL) - f1-9 (POL)
    Always
    Below 1 Ω
    I3-19 (LMT) - f1-10 (HND)
    Always
    Below 1 Ω
    I3-13 (OSG) - f1-8 (E1)
    Always
    Below 1 Ω
    I4-1 (DC-) or f1-1 (ACT-) - Body ground
    Always
    10 kΩ or higher
    I4-5 (DC+) or f1-2 (ACT+) - Body ground
    Always
    10 kΩ or higher
    I3-4 (HAF) or f1-3 (HAF) - Body ground
    Always
    10 kΩ or higher
    I3-5 (FUL) or f1-4 (FUL) - Body ground
    Always
    10 kΩ or higher
    I3-18 (POL) or f1-9 (POL) - Body ground
    Always
    10 kΩ or higher
    I3-19 (LMT) or f1-10 (HND) - Body ground
    Always
    10 kΩ or higher
    I3-13 (OSG) or f1-8 (E1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Slide Door Closer Motor LH Circuit (from Dec 2015)Slide Door Closer Relay Power Source Circuit (Oct 2014 – Nov 2015) →