2014-2019 Hiace · Service Manual BODY ELECTRICAL

Door Control Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The instrument panel junction block assembly (body ECU) receivers the door lock/unlock request signal from the power window regulator master switch assembly*1 or door control switch assembly*2. The instrument panel junction block assembly (body ECU) actives the door lock motor on all door according to the signal.
  1. *1: w/ Power Window Control System
  2. *2: w/o Power Window Control System

WIRING DIAGRAM

E292511E05
E292511E06

INSPECTION PROCEDURE


1. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    w/ Power Window Control System
    A
    w/o Power Window Control System
    B



B
Go to step 4
A


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)
  1. Remove the power window regulator master switch assembly (Click here).

  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY AND BODY GROUND)
  1. Disconnect the 13B instrument panel junction block assembly (body ECU) connector.

  1. Disconnect the L5*1 or K5*2 power window regulator master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    13B-23 (L1) - L5-5 (L)
    Always
    Below 1 Ω
    13B-24 (UL1) - L5-8 (UL)
    Always
    Below 1 Ω
    L5-1 (GND) - Body ground
    Always
    Below 1 Ω
    13B-23 (L1) or L5-5 (L) - Body ground
    Always
    10 kΩ or higher
    13B-24 (UL1) or L5-8 (UL) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    13B-6 (L1) - K5-5 (L)
    Always
    Below 1 Ω
    13B-5 (UL1) - K5-8 (UL)
    Always
    Below 1 Ω
    K5-1 (GND) - Body ground
    Always
    Below 1 Ω
    13B-6 (L1) or K5-5 (L) - Body ground
    Always
    10 kΩ or higher
    13B-5 (UL1) or K5-8 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. INSPECT DOOR CONTROL SWITCH ASSEMBLY
  1. Remove the door control switch assembly.

  1. Inspect the door control switch assembly (Click here).



NG
REPLACE DOOR CONTROL SWITCH ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - DOOR CONTROL SWITCH ASSEMBLY AND BODY GROUND)
  1. Disconnect the 13H instrument panel junction connector assembly (body ECU) connector.

  1. Disconnect the I25 door control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    13H-6 (L1) - I25-5 (L)
    Always
    Below 1 Ω
    13H-7 (UL1) - I25-4 (UL)
    Always
    Below 1 Ω
    I25-6 (E) - Body ground
    Always
    Below 1 Ω
    13H-6 (L1) or I25-5 (L) - Body ground
    Always
    10 kΩ or higher
    13H-7 (UL1) or I25-4 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Door Control Switch Circuit (Jan 2015 – Dec 2016)PRECAUTION (from Oct 2014) →