2014-2019 Hiace · Service Manual BODY ELECTRICAL

B2430 LED Headlight LH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Dec 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The illumination of the low beam headlights is controlled by the instrument panel junction block (main body ECU). When the headlights are turned on, the headlight leveling ECU receives a signal from the headlight light control ECU and detects the illumination condition of the low beam headlights.
DTC Code
DTC Detection Condition
Trouble Area
B2430
LED headlight LH circuit malfunction
  1. Headlight light control ECU sub-assembly LH
  2. Headlight assembly LH
  3. Headlight leveling ECU assembly
  4. Instrument panel junction block (main body ECU)
  5. Instrument panel relay block
  6. Harness or connector
B2431
LED headlight RH circuit malfunction
  1. Headlight light control ECU sub-assembly RH
  2. Headlight assembly RH
  3. Headlight leveling ECU assembly
  4. Instrument panel junction block (main body ECU)
  5. Instrument panel relay block
  6. Harness or connector

HINT:
DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned to ON.


WIRING DIAGRAM

E289819E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
After replacing the headlight leveling ECU, initialization of the ECU is necessary (Click here).


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT INSTRUMENT PANEL RELAY BLOCK

  1. E291485E01
    Remove the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12A-1 - 12B-9
    Battery voltage not applied between terminals 12A-1 and 12B-10
    10 kΩ or higher
    Battery voltage applied between terminals 12A-1 and 12B-10
    Below 1 Ω
    12A-1 - 12D-3
    Battery voltage not applied between terminals 12A-1 and 12D-4
    10 kΩ or higher
    Battery voltage applied between terminals 12A-1 and 12D-4
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL RELAY BLOCK
OK


4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - INSTRUMENT PANEL JUNCTION BLOCK [BODY ECU] AND BATTERY)
  1. Disconnect the 12A, 12B and 12D instrument panel relay block connectors.

  1. Disconnect the 13E instrument panel junction block (main body ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    12A-1 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12B-10 - 13E-20 (HRLY)
    Always
    Below 1 Ω
    12D-4 - 13E-20 (HRLY)
    12B-10 - Body ground
    Always
    10 kΩ or higher
    12D-4 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - HEADLIGHT ASSEMBLY)
  1. Disconnect the 12B and 12D instrument panel relay block connectors.

  1. Disconnect the A36*1 and A33*2 headlight connectors.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    12B-9 - A36-6 (LO)
    Always
    Below 1 Ω
    12B-9 - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    12D-3 - A33-6 (LO)
    Always
    Below 1 Ω
    12D-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY AND BODY GROUND)
  1. Disconnect the A39 headlight leveling ECU connector.

  1. Disconnect the A36*1 and A33*2 headlight connectors.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A36-5 (S) - A39-3 (LLEW)
    Always
    Below 1 Ω
    A36-4 (E) - Body ground
    A36-5 (S) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A33-5 (S) - A39-2 (RLEW)
    Always
    Below 1 Ω
    A33-4 (E) - Body ground
    A33-5 (S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT HEADLIGHT ASSEMBLY

  1. E289820E01
    Remove the headlight (Click here).

  1. Disconnect the headlight light control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (LO) - A-1
    Always
    Below 1 Ω
    5 (S) - A-7
    4 (E) - A-3

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Light Control ECU Sub-assembly)
    *b
    Component without harness connected
    (Headlight Assembly)



NG
REPLACE HEADLIGHT ASSEMBLY (Click here)
OK


8. CHECK HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY
  1. Temporarily replace the headlight light control ECU with a new or normally functioning one.for LHD: Click here for RHD: Click here

  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
Go to step 9
OK

END (HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY WAS DEFECTIVE)

9. CHECK HEADLIGHT ASSEMBLY (LED UNIT)
  1. Temporarily replace the headlight (LED unit) with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
Go to step 10
OK

END (HEADLIGHT ASSEMBLY [LED UNIT] WAS DEFECTIVE)

10. CHECK HEADLIGHT LEVELING ECU ASSEMBLY
  1. Temporarily replace the headlight leveling ECU with a new or normally functioning one.for LHD: Click here for RHD: Click here

  1. Check for DTCs (Click here).

    OK:
    DTC B2430 or B2431 output does not occur.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
OK

END (HEADLIGHT LEVELING ECU ASSEMBLY WAS DEFECTIVE)


← B2430 LED Headlight LH Circuit Malfunction (+ B2431) (Oct 2014 – Dec 2014)B2430 LED Headlight LH Circuit Malfunction (+ B2431) (from Jan 2017) →