B2430 LED Headlight LH Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- B2431 LED Headlight RH Circuit Malfunction
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
The illumination of the low beam headlights is controlled by the instrument panel junction block (main body ECU). When the headlights are turned on, the headlight leveling ECU receives a signal from the headlight light control ECU and detects the illumination condition of the low beam headlights.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2430 |
LED headlight LH circuit malfunction |
|
| B2431 |
LED headlight RH circuit malfunction |
|
- HINT:
- DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned to ON.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- After replacing the headlight leveling ECU, initialization of the ECU is necessary (Click here).
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
| 3. INSPECT INSTRUMENT PANEL RELAY BLOCK |
Remove the instrument panel relay block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
12A-1 - 12B-9
Battery voltage not applied between terminals 12A-1 and 12B-10
10 kΩ or higher
Battery voltage applied between terminals 12A-1 and 12B-10
Below 1 Ω
12A-1 - 12D-3
Battery voltage not applied between terminals 12A-1 and 12D-4
10 kΩ or higher
Battery voltage applied between terminals 12A-1 and 12D-4
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - INSTRUMENT PANEL JUNCTION BLOCK [BODY ECU] AND BATTERY) |
Disconnect the 12A, 12B and 12D instrument panel relay block connectors.
Disconnect the 13E instrument panel junction block (main body ECU) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
12A-1 - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
12B-10 - 13E-20 (HRLY)
Always
Below 1 Ω
12D-4 - 13E-20 (HRLY)
12B-10 - Body ground
Always
10 kΩ or higher
12D-4 - Body ground
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - HEADLIGHT ASSEMBLY) |
Disconnect the 12B and 12D instrument panel relay block connectors.
Disconnect the A36*1 and A33*2 headlight connectors.
- *1: for LH
- *2: for RH
- *1: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
12B-9 - A36-6 (LO)
Always
Below 1 Ω
12B-9 - Body ground
Always
10 kΩ or higher
- for RH:
Tester Connection
Condition
Specified Condition
12D-3 - A33-6 (LO)
Always
Below 1 Ω
12D-3 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY AND BODY GROUND) |
Disconnect the A39 headlight leveling ECU connector.
Disconnect the A36*1 and A33*2 headlight connectors.
- *1: for LH
- *2: for RH
- *1: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
A36-5 (S) - A39-3 (LLEW)
Always
Below 1 Ω
A36-4 (E) - Body ground
A36-5 (S) - Body ground
Always
10 kΩ or higher
- for RH:
Tester Connection
Condition
Specified Condition
A33-5 (S) - A39-2 (RLEW)
Always
Below 1 Ω
A33-4 (E) - Body ground
A33-5 (S) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT HEADLIGHT ASSEMBLY |
Remove the headlight (Click here).

Disconnect the headlight light control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
6 (LO) - A-1
Always
Below 1 Ω
5 (S) - A-7
4 (E) - A-3
Text in Illustration *a
Front view of wire harness connector
(to Headlight Light Control ECU Sub-assembly)
*b
Component without harness connected
(Headlight Assembly)
|
|
||||
| OK | |
| 8. CHECK HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY |
Temporarily replace the headlight light control ECU with a new or normally functioning one.for LHD: Click here for RHD: Click here
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
| 9. CHECK HEADLIGHT ASSEMBLY (LED UNIT) |
Temporarily replace the headlight (LED unit) with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
| 10. CHECK HEADLIGHT LEVELING ECU ASSEMBLY |
Temporarily replace the headlight leveling ECU with a new or normally functioning one.for LHD: Click here for RHD: Click here
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
