2014-2019 Hiace · Service Manual BODY ELECTRICAL

B2416 Height Control Sensor Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The headlight leveling ECU receives signals indicating the height of the vehicle from the rear height control sensor.
DTC Code
DTC Detection Condition
Trouble Area
B2416
  1. Malfunction in the rear height control sensor.
  2. Open or short in the rear height control sensor circuit.
  1. Rear height control sensor sub-assembly LH
  2. Harness or connector
  3. Headlight leveling ECU assembly
B241A

WIRING DIAGRAM

E225964E08

INSPECTION PROCEDURE

HINT:
After replacing the headlight leveling ECU and rear height control sensor, initialization of the ECU is necessary (Click here).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 or B241A output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)
  1. Using the GTS, read the Data List (Click here).

    HL AutoLeveling 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Sens Pw Supply Val
    Rear height control sensor power supply value / 0 to 5 V
    Approximately 5.0 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value / 0 to 5 V
    Approximately 2.5 V (when vehicle level)
    The value changes according to the vehicle height.

    OK:
    The display is as specified in the normal condition column.
    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

C
Go to step 3
A

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
  1. Disconnect the A39 headlight leveling ECU connector.

  1. Disconnect the P2 rear height control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-12 (SBR) - P2-3 (SHB)
    Always
    Below 1 Ω
    A39-19 (SHRL) - P2-2 (SHRR)
    Always
    Below 1 Ω
    A39-21 (SGR) - P2-1 (SHG)
    Always
    Below 1 Ω
    A39-12 (SBR) - Body ground
    Always
    10 kΩ or higher
    A39-19 (SHRL) - Body ground
    Always
    10 kΩ or higher
    A39-21 (SGR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
  1. Remove the rear height control sensor (Click here).

  1. Inspect the rear height control sensor (Click here).

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

C
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
A

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)


← B2416 Height Control Sensor Malfunction (+ B241A) (Jan 2015 – Dec 2016)B2420 HL AutoLeveling ECU Failure (Oct 2014 – Dec 2014) →