2014-2019 Hiace · Service Manual BODY ELECTRICAL

Headlight Beam Level Control Actuator Circuit

Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The headlight leveling ECU actuates the headlight leveling motors according to the vehicle conditions.

WIRING DIAGRAM

E290810E01

INSPECTION PROCEDURE

HINT:
After replacing the headlight leveling ECU, initialization of the ECU is necessary (Click here).


1. PERFORM ACTIVE TEST USING GTS (HEADLIGHT LEVELING MOTOR)
  1. Using the GTS, perform the Active Test (Click here).

    HL Auto Leveling 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor
    Leveling motor upward or downward operation
    Stop/Down/Up
    Perform the Active Test with the engine started and vehicle stopped.

    OK:
    Headlight leveling motors operate normally.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
  1. Disconnect the A39 headlight leveling ECU connector.

  1. Disconnect the A38*1 or A35*2 headlight leveling motor connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A39-11 (LH+) - A38-3 (LHIG)
    Always
    Below 1 Ω
    A39-18 (LHT) - A38-2 (LH T)
    A39-24 (LH-) - A38-1 (LH E)
    A39-11 (LH+) - Body ground
    Always
    10 kΩ or higher
    A39-18 (LHT) - Body ground
    A39-24 (LH-) - Body ground
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A39-10 (RH+) - A35-3 (RHIG)
    Always
    Below 1 Ω
    A39-17 (RHT) - A35-2 (RH T)
    Always
    Below 1 Ω
    A39-23 (RH-) - A35-1 (RH E)
    Always
    Below 1 Ω
    A39-10 (RH+) - Body ground
    Always
    10 kΩ or higher
    A39-17 (RHT) - Body ground
    Always
    10 kΩ or higher
    A39-23 (RH-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HEADLIGHT UNIT (OPERATION)
  1. Temporarily replace the headlight assembly (headlight leveling motor) with a new or normally functioning one (Click here).

  1. Perform the Active Test of the leveling motors.

    OK:
    Headlight leveling motors operate normally.

Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

C
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)
A

END (HEADLIGHT ASSEMBLY IS DEFECTIVE)


← Headlight Beam Level Control Actuator Circuit (Jan 2015 – Mar 2016)Headlight Beam Level Control Actuator Circuit (from Jan 2017) →