2014-2019 Hiace · Service Manual ENGINE

P2444 Secondary Air Injection System Pump Stuck On Bank1

Diagnostic trouble codes · Vehicles built Dec 2015 – Mar 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Refer to P2431 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2444
Secondary air pressure more than 3.3 kPa (25 mmHg) despite ECM commanding air pump to turn off (2 trip detection logic)
  1. Short in air pump circuit
  2. Open or short in air pressure sensor circuit
  3. Air pressure sensor
  4. Air injection control driver
  5. ECM
P2445
Secondary air pressure less than 1.0 kPa (7.5 mmHg) despite ECM commanding air pump to turn on (2 trip detection logic)
  1. Air pump
  2. Open in air pump circuit
  3. Secondary air injection system piping
  4. Vacuum hose (air pressure sensor - air switching valve)
  5. Air pressure sensor
  6. Open or short in air pressure sensor circuit
  7. Air injection control driver
  8. ECM

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the air switching valve of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and sets a DTC:
  1. The pressure indicated by the air pressure sensor does not reach threshold levels despite the ECM turning on the air pump.
  2. The pressure indicated by the air pressure sensor exceeds threshold levels despite the ECM turning off the air pump.

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

HINT:
  1. By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing System Check / Automatic Mode after the repair.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND/OR P2445)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P2444 and/or P2445 is output
    A
    DTC P2444 and/or P2445, and P0418 are output
    B
    DTC P2444 and/or P2445, and other DTCs (except P0418) are output
    C
    If any DTCs other than P2444, P2445 and/or P0418 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE (Click here)

C
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and air switching valve operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Check that the air pump (AIR PUMP), air switching valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) status displayed on the intelligent tester, indicate the conditions shown in the table below.

    Standard:
    Tester Operation
    AIR PUMP
    ASV
    PRESSURE*
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    1 kPa or more
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Less than 3.3 kPa

    *: Average pumping pressure. The pressure should be 1 kPa or more when the secondary air injection system operates.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (Wait or Error).
      If an Error is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (if set) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the intelligent tester initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

    Result 
    Result
    Proceed to
    DTC P2444 and/or P2445 is output
    A
    No pending DTC
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4. CHECK VACUUM HOSES (AIR PRESSURE SENSOR - AIR SWITCHING VALVE)
  1. Check the vacuum hose connections with the air pressure sensor and air switching valve.

  1. Inspect the vacuum hose for blockages and damage.

    OK:
    Vacuum hose has no blockages or damage.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5. INSPECT AIR PRESSURE SENSOR

  1. A263362
    Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).

  1. Check that the pressure displayed on the intelligent tester fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The intelligent tester displays the air pump pressure (Air Pump Pressure (Absolute)) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR (Click here)
OK


6. CHECK SECONDARY AIR INJECTION SYSTEM PIPE CONNECTIONS
A261569
  1. Check that all the pipes and hoses between the air pump and air switching valve are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    Secondary air injection system piping has no blockages or damage.



NG
REPAIR OR REPLACE SECONDARY AIR INJECTION SYSTEM PIPING
OK


7. INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A115629E07
  1. Disconnect the air injection control driver connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B14-1 (BATT) - Body ground
    Always
    11 to 14 V
    B12-5 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B12-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Driver)



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


8. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B71-12 (AIRP) - B12-4 (SIP)
    Always
    Below 1 Ω
    B71-12 (AIRP) or B12-4 (SIP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT AIR PUMP ASSEMBLY
A222978E02
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the 400 A probe of an ammeter to the (+) wire of the air pump.

    Text in Illustration 
    *1
    Air Pump Wire
    *2
    Air Injection Control Driver

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Measure the current while the air pump is on and off.

    Standard Current:
    Tester Operation
    Air Pump
    ASV
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    ON
    OPEN
    10 to 40 A
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    CLOSE
    Below 1 A

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While AIR system operation using the intelligent tester is prohibition (WAIT or ERROR).
      If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected. Wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 13
OK


10. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Disconnect the air injection control driver connector.

  1. A229922E46
    Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-3 (SIV) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. A229922E47
    Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-4 (SIP) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


11. REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


12. CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (if set) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the intelligent tester initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END

13. REPLACE AIR PUMP ASSEMBLY
  1. Replace the air pump assembly (Click here).


NEXT


14. CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (if set) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the intelligent tester initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 15
OK

END

15. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Disconnect the air injection control driver connector.

  1. A229922E46
    Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-3 (SIV) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. A229922E47
    Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-4 (SIP) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


16. REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


17. CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (if set) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the intelligent tester initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END


← P2444 Secondary Air Injection System Pump Stuck On Bank1 (+ P2445) (Jan 2015 – Nov 2015)P2444 Secondary Air Injection System Pump Stuck On Bank1 (+ P2445) (Apr 2016 – Dec 2016) →