2014-2019 Hiace · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2017 from Dec 2017


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Powertrain / Engine and ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    N Range Status
    Shift lever N Range Status/
    ON or OFF
    Shift lever position is:
    1. P or N: ON
    2. Except P or N: OFF
    -
    Neutral Position SW Signal
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. P or N: ON
    2. Except P or N: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Stop Light Switch
    Stop light SW Status/
    ON or OFF
    1. Brake Pedal is depressed: ON
    2. Brake Pedal is released: OFF
    -
    SPD (NCO)
    Input turbine Speed/
    Min.: 0 rpm
    Max.: 12750 rpm

    HINT:
    1. Lock-up ON (warmed up engine, other than O/D):
      Input Turbine Speed (NCO) is equal to engine speed
    2. Lock-up ON (warmed up engine, O/D):
      Input Turbine Speed (NCO) is 0 rpm
    3. Lock-up OFF (Idling with shift lever on N):
      Input Turbine Speed (NCO) is nearly equal to engine speed

    Data is displayed in increments of 50 rpm
    SPD (SP2)
    Output shaft Speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)

    HINT:
    Equal to vehicle speed

    -
    Shift SW Status (P Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. P: ON
    2. Except P: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (R Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. R: ON
    2. Except R: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. 2: ON
    2. Except 2: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. L: ON
    2. Except L: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (N Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. N: ON
    2. Except N: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (N, P Range) Supported
    Status of park/neutral position switch (N or P) supported/
    Unsupp or Supp
    -
    -
    Shift SW Status (N, P Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever position is:
    1. P or N: ON
    2. Except P or N: OFF
    -
    Shift SW Status (D Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. D or 3: ON
    2. Except D or 3: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. 3: ON
    2. Except 3: OFF
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    A/T Oil Temperature 3
    ATF Temp. Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor No.1 circuit is open or shorted.
    Lock Up
    Lock up/
    ON or OFF
    Lock-up is:
    1. ON: Operating
    2. OFF: Not operating
    -
    Shift Status
    Actual Gear position/
    1st, 2nd, 3rd or 4th (O/D)
    Shift lever position is;
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)
    -
    SLT Solenoid Status
    Shift Solenoid SLT Status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SL Solenoid Status
    Shift solenoid SL status/
    ON or OFF
    Shift solenoid SL is:
    1. ON: Operating
    2. OFF: Not operating
    -


ACTIVE TEST

HINT:
Performing the GTS Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Powertrain / Engine and ECT / Active Test".

  7. Follow the instructions on the tester and perform the Active Test.

    except TRH223L-LEPNK and TRH223L-LDPNK 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Line Pressure Up*
    Operate the shift solenoid SLT and raise the line pressure.
    ON or OFF

    HINT:
    1. OFF: Line pressure up (When the active test of "Control the Line Pressure Up" is performed, the ECM commands the SLT solenoid to turn off).
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Control the Lock Up
    Control the shift solenoid SL to set the automatic transmission to the lock-up condition.
    ON or OFF
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Control the Shift Position
    Operate the shift solenoid valve and set each shift position by yourself.
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    [Vehicle Condition]
    50 km/h (31 mph) or less
    *: "Control the Line Pressure Up" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

    TRH223L-LEPNK and TRH223L-LDPNK 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Connects and disconnects TC and TE1. (transitions into the fluid temperature detection mode)
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate the shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine is stopped
    3. Shift lever in P or N
    Activate the Solenoid (S2)
    Operate the shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine is stopped
    3. Shift lever in P or N
    Activate the Lock Up
    Control shift solenoid valve SL to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SL operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Activate the Solenoid (SL)
    Operate the shift solenoid SL
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine is stopped
    3. Shift lever in P or N
    Control the Shift Position
    Operate shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (31 mph) or less
    *: "Activate the Solenoid (SLT)" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

← FAIL-SAFE CHART (from Oct 2014)DATA LIST / ACTIVE TEST (Jan 2015 – Nov 2017) →