DATA LIST / ACTIVE TEST
System information · Vehicles built Jan 2015 – Nov 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2017 from Dec 2017
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Enter / Powertrain / Engine and ECT / Data List".
Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
N Range Status
Shift lever N Range Status/
ON or OFF
Shift lever position is: - P or N: ON
- Except P or N: OFF
-
Neutral Position SW Signal
PNP SW Status/
ON or OFF
Shift lever position is: - P or N: ON
- Except P or N: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Stop Light Switch
Stop light SW Status/
ON or OFF
- Brake Pedal is depressed: ON
- Brake Pedal is released: OFF
-
SPD (NCO)
Input turbine Speed/
Min.: 0 rpm
Max.: 12750 rpm
- HINT:
- Lock-up ON (warmed up engine, other than O/D):
Input Turbine Speed (NCO) is equal to engine speed
- Lock-up ON (warmed up engine, O/D):
Input Turbine Speed (NCO) is 0 rpm
- Lock-up OFF (Idling with shift lever on N):
Input Turbine Speed (NCO) is nearly equal to engine speed
- Lock-up ON (warmed up engine, other than O/D):
Data is displayed in increments of 50 rpm
SPD (SP2)
Output shaft Speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) - HINT:
- Equal to vehicle speed
-
Shift SW Status (P Range)
PNP SW Status/
ON or OFF
Shift lever position is: - P: ON
- Except P: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (R Range)
PNP SW Status/
ON or OFF
Shift lever position is: - R: ON
- Except R: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (2 Range)
PNP SW Status/
ON or OFF
Shift lever position is: - 2: ON
- Except 2: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (L Range)
PNP SW Status/
ON or OFF
Shift lever position is: - L: ON
- Except L: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (N Range)
PNP SW Status/
ON or OFF
Shift lever position is: - N: ON
- Except N: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (N, P Range) Supported
Status of park/neutral position switch (N or P) supported/
Unsupp or Supp
-
-
Shift SW Status (N, P Range)
Park/neutral position switch status/
ON or OFF
Shift lever position is: - P or N: ON
- Except P or N: OFF
-
Shift SW Status (D Range)
PNP SW Status/
ON or OFF
Shift lever position is: - D or 3: ON
- Except D or 3: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (3 Range)
PNP SW Status/
ON or OFF
Shift lever position is: - 3: ON
- Except 3: OFF
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
A/T Oil Temperature 3
ATF Temp. Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test;
Approx. 80°C (176°F)
- Equal to ambient temperature when cold soak
If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor No.1 circuit is open or shorted.
Lock Up
Lock up/
ON or OFF
Lock-up is: - ON: Operating
- OFF: Not operating
-
Shift Status
Actual Gear position/
1st, 2nd, 3rd or 4th (O/D)
Shift lever position is; - L: 1st
- 2: 1st or 2nd
- 3: 1st, 2nd or 3rd
- D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)
-
SLT Solenoid Status
Shift Solenoid SLT Status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
SL Solenoid Status
Shift solenoid SL status/
ON or OFF
Shift solenoid SL is: - ON: Operating
- OFF: Not operating
-
- P or N: ON
| ACTIVE TEST |
- HINT:
- Performing the GTS Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Enter / Powertrain / Engine and ECT / Active Test".
Follow the instructions on the tester and perform the Active Test.
*: "Control the Line Pressure Up" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST Click here) as well.except TRH223L-LEPNK and TRH223L-LDPNK Tester Display
Test Part
Control Range
Diagnostic Note
Control the Line Pressure Up*
Operate the shift solenoid SLT and raise the line pressure.
ON or OFF - HINT:
- OFF: Line pressure up (When the active test of "Control the Line Pressure Up" is performed, the ECM commands the SLT solenoid to turn off).
- ON: No action (normal operation)
- OFF: Line pressure up (When the active test of "Control the Line Pressure Up" is performed, the ECM commands the SLT solenoid to turn off).
[Vehicle Condition] - Vehicle stopped
- Engine idling
Control the Lock Up
Control the shift solenoid SL to set the automatic transmission to the lock-up condition.
ON or OFF
[Vehicle Condition] - Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (37 mph) or more
Control the Shift Position
Operate the shift solenoid valve and set each shift position by yourself.
- Press "→" button: Shift up
- Press "←" button: Shift down
[Vehicle Condition]
50 km/h (31 mph) or less
- HINT:
- The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.
*: "Activate the Solenoid (SLT)" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.TRH223L-LEPNK and TRH223L-LDPNK Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Connects and disconnects TC and TE1. (transitions into the fluid temperature detection mode)
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Shift lever in P or N
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
- ON: No action (normal operation)
- OFF: Line pressure up (when Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Activate the Solenoid (S1)
Operate the shift solenoid S1
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate the shift solenoid S2
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid valve SL to set automatic transmission to lock-up condition
ON or OFF
Possible to check shift solenoid valve SL operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (37 mph) or more
Activate the Solenoid (SL)
Operate the shift solenoid SL
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
- HINT:
- The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.