2014-2019 Hiace · Service Manual BODY

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

  1. Check the operation of the mirror surface.

    1. Disconnect the outer rear view mirror assembly LH connector.

    2. B366748E01
      Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 3 (MV)
      Battery negative (-) → Terminal 7 (M+)
      Turns upward
      Battery positive (+) → Terminal 7 (M+)
      Battery negative (-) → Terminal 3 (MV)
      Turns downward
      Battery positive (+) → Terminal 6 (MH)
      Battery negative (-) → Terminal 7 (M+)
      Turns left
      Battery positive (+) → Terminal 7 (M+)
      Battery negative (-) → Terminal 6 (MH)
      Turns right

      If the result is not as specified, replace the outer mirror retractor LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.


    1. B366747E01
      Disconnect the outer rear view mirror assembly LH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Forward position A
      Moves from A to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Forward position A
      Does not move
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Position between forward position A and driving position C
      Moves from B to forward position A
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Driving position C
      Moves from C to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Driving position C
      Does not move
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Position between driving position C and retracted position E
      Moves from D to driving position C
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Retracted position E
      Does not move
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Retracted position E
      Moves from E to driving position C

      If the result is not as specified, replace the outer mirror retractor LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

  1. Check the operation of the mirror surface.

    1. B366745E01
      Disconnect the outer rear view mirror assembly RH connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 3 (MV)
      Battery negative (-) → Terminal 7 (M+)
      Turns upward
      Battery positive (+) → Terminal 7 (M+)
      Battery negative (-) → Terminal 3 (MV)
      Turns downward
      Battery positive (+) → Terminal 6 (MH)
      Battery negative (-) → Terminal 7 (M+)
      Turns left
      Battery positive (+) → Terminal 7 (M+)
      Battery negative (-) → Terminal 6 (MH)
      Turns right

      If the result is not as specified, replace the outer mirror retractor RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.


    1. B366744E01
      Disconnect the outer rear view mirror assembly RH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Forward position A
      Moves from A to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Forward position A
      Does not move
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Position between forward position A and driving position C
      Moves from B to forward position A
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Driving position C
      Moves from C to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Driving position C
      Does not move
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position E
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Position between driving position C and retracted position E
      Moves from D to driving position C
      Battery positive (+) → Terminal 1 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Retracted position E
      Does not move
      Battery positive (+) → Terminal 2 (MF)
      Battery negative (-) → Terminal 1 (MR)
      Retracted position E
      Moves from E to driving position C

      If the result is not as specified, replace the outer mirror retractor RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →