2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017 from Dec 2017

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. INSTALL CYLINDER HEAD GASKET

  1. A060285E02
    Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.
    Text in Illustration 
    *1
    Measuring Tip
    *2
    Protrusion

  1. A058134E02
    Measure the piston protrusion of each cylinder at 2 points as shown in the illustration.
    Text in Illustration 
    *1
    Measuring Point

  1. For the piston protrusion value of each cylinder, use the average of the 2 measurements of that cylinder.

    Standard piston protrusion:
    0.005 to 0.254 mm (0.0002 to 0.0100 in.)

    HINT:
    If the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.

  1. A060174E02
    Select a new cylinder head gasket.
    Text in Illustration 
    *1
    Cutout Mark
    V100135
    Front

    HINT:
    New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.

    New Installed Cylinder Head Gasket Thickness:
    Item
    Specified Condition
    Mark A
    0.80 to 0.90 mm (0.0315 to 0.0354 in.)
    Mark B
    0.85 to 0.95 mm (0.0335 to 0.0374 in.)
    Mark C
    0.90 to 1.00 mm (0.0354 to 0.0394 in.)
    Mark D
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    Mark E
    1.00 to 1.10 mm (0.0394 to 0.0433 in.)


    1. Select the largest piston protrusion value from the measurements made. Then select a new appropriate gasket according to the table below.

      Gasket Size to be Used:
      Gasket Size
      Piston Protrusion
      A
      0.005 to 0.054 mm (0.0002 to 0.0021 in.)
      B
      0.055 to 0.104 mm (0.0022 to 0.0041 in.)
      C
      0.105 to 0.154 mm (0.0041 to 0.0061 in.)
      D
      0.155 to 0.204 mm (0.0061 to 0.0080 in.)
      E
      0.205 to 0.255 mm (0.0081 to 0.0100 in.)

  1. A060144E02
    Place the cylinder head on the cylinder block.

    1. Place the cylinder head gasket on the cylinder block.

      Text in Illustration 
      V100135
      Front

      NOTICE:
      Make sure the gasket is installed in the correct direction.

    2. Place the cylinder head on the cylinder head gasket.


2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
  1. The cylinder head bolts are tightened in 3 progressive steps.
  2. If any bolt is broken or deformed, replace it.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. A060284E01
    Install the 18 cylinder head bolts and 18 washers and tighten the bolts in several passes in the sequence shown in the illustration.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    Standard Bolt Length:
    Item
    Specified Condition
    A
    110 mm (4.33 in.)
    B
    167 mm (6.57 in.)

    If any of the cylinder head bolts does not meet the torque specification, replace it.

  1. A060141E03
    Mark the front of the cylinder head bolts with paint.
    Text in Illustration 
    *1
    Paint Mark
    *a
    Front

  1. Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.

  1. Finally, tighten the cylinder head bolts by an additional 90°.

  1. Check that the paint marks are now facing rearward.


3. INSTALL EXHAUST MANIFOLD
  1. Set a new gasket on the cylinder head.

  1. Install the exhaust manifold, 8 collars and 8 plate washers with 8 new nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Install the collars so that the side with the smaller external diameter faces the exhaust manifold.


4. INSTALL INTAKE MANIFOLD (w/o DPF)
  1. Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.

  1. A172284E01
    Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Make sure that the swirl control valve actuator is not damaged by the surrounding parts.


5. INSTALL SWIRL CONTROL VALVE ASSEMBLY (w/ DPF)

  1. A239323E01
    Temporarily install a new gasket and the swirl control valve with the 4 bolts and 2 nuts.

    NOTICE:
    Make sure that the swirl control valve actuator is not damaged by the surrounding parts.

  1. Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


6. INSTALL VACUUM SWITCHING VALVE SET (w/ DPF)
  1. Install the vacuum control valve set with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 3 vacuum hoses and 2 connectors.

    HINT:
    A265827E01
    When connecting the hoses, match the color of the paint mark on the hoses to the color of the paint mark on the swirl control valve as shown in the illustration.


7. INSTALL INTAKE MANIFOLD (w/ DPF)
  1. Temporarily install a new gasket and the intake manifold with the 7 bolts and 2 nuts.

  1. A239322E01
    Tighten the 7 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the vacuum hoses.


8. INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ DPF)
  1. Install the No. 1 intake manifold insulator to the intake manifold.


9. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


10. INSTALL CYLINDER BLOCK INSULATOR
  1. Install the cylinder block insulator to the cylinder head.


11. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Temporarily install the No. 1 compressor mounting bracket with the 4 bolts.

  1. A264145E01
    Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

    HINT:
    Make sure that the No. 1 compressor mounting bracket is in contact with the cylinder block.


12. INSTALL CAMSHAFT
(Click here)

13. INSTALL TIMING BELT
(Click here)

14. INSPECT AND ADJUST VALVE CLEARANCE
(Click here)

15. INSTALL TURBOCHARGER SUB-ASSEMBLY
(Click here)

16. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

17. INSTALL GLOW PLUG ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

18. INSTALL INJECTOR ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

19. INSTALL EGR COOLER ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

20. INSTALL COMMON RAIL ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

21. CHARGE REFRIGERANT (w/ Air Conditioning System)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    E100257E01

    Standard:
    Single A/C:
    520 to 580g (18.3 to 20.5 oz.)
    Dual A/C:
    670 to 730g (23.0 to 25.7 oz.)

    SST
    07110-58060   (07117-58090, 07117-78050, 07117-58070, 07117-58060, 07117-58080, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant, which causes the compressor to overheat.
    2. Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

    HINT:
    Prepare a service can to recharge refrigerant if using the refrigerant gas collected with the freon collection/recycling device because the collective rate of the device is approximately 90%.


22. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:
    Item
    Oil Grade
    Oil Viscosity (SAE)
    w/ DPF
    ACEA C2
    (Using engine oil other than ACEA C2 may damage catalytic converter)
    - 0W-30
    - 5W-30
    w/o DPF
    G-DLD1, API CF-4, CF or ACEA B1
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50


    Standard Capacity (w/ DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Drain and refill with oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Dry fill
    7.5 liters (7.9 US qts, 6.6 Imp. qts)


    Standard Capacity (w/o DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts, 6.2 Imp. qts)
    Dry fill
    7.7 liters (8.1 US qts, 6.8 Imp. qts)

  1. Install the oil filler cap.


23. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs.

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/ Front Heater
    14.2 liters (15.0 US qts, 12.5 Imp. qts)
    w/ Front and Rear Heaters
    16.2 liters (17.1 US qts, 14.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Loosen the bleeder plug of the outlet housing.

  1. When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A142533
    Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.


24. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


25. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Hot, pressurized engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


26. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

27. INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)
  1. After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E02
    Using a gas leak detector, check for leakage of the refrigerant line.

  1. N014519E01
    Bring the gas leak detector close to the drain hose with the detector's power off.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If such reaction is unavoidable, the vehicle must be lifted up.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.


28. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait for 5 minutes.

  1. Check that the oil level is between the upper level and lower level of the engine oil level dipstick.
    If the oil level is low, check for leakage and add oil up to the upper level of the oil level dipstick.

← INSTALLATION (Jan 2015 – Mar 2016)INSTALLATION (from Jan 2017) →