2014-2019 Hiace · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Oct 2014


1. REPLACE INTAKE VALVE GUIDE BUSH

A053808E02
  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A059922E02
    Using SST and a hammer, tap out the valve guide bush.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

  1. A059167E01
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Select new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    Use STD
    10.985 to 11.006 mm
    (0.4325 to 0.4333 in.)
    Use O/S 0.05
    11.035 to 11.056 mm
    (0.4344 to 0.4353 in.)

    If the bush bore diameter of the cylinder head is greater than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 to 11.056 mm (0.4344 to 0.4353 in.).
    If the bush bore diameter of the cylinder head is greater than 11.056 mm (0.4353 in.), replace the cylinder head.

  1. A061560E02
    Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Standard protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)

  1. A059166E01
    Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.


2. REPLACE EXHAUST VALVE GUIDE BUSH

A053808E02
  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A059923E01
    Using SST and a hammer, tap out the valve guide bush.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

  1. A059172E01
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Select new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    Use STD
    10.985 to 11.006 mm
    (0.4325 to 0.4333 in.)
    Use O/S 0.05
    11.035 to 11.056 mm
    (0.4344 to 0.4353 in.)

    If the bush bore diameter of the cylinder head is greater than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 to 11.056 mm (0.4344 to 0.4353 in.).
    If the bush bore diameter of the cylinder head is greater than 11.056 mm (0.4353 in.), replace the cylinder head.

  1. A061559E01
    Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Standard protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)

  1. A059170E01
    Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

← INSPECTION (from Oct 2014)REASSEMBLY (from Oct 2014) →