2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT STARTER ARMATURE ASSEMBLY
  1. If the surface of the commutator is dirty or burned, polish the part with sandpaper (#400) or replace the armature.

  1. ST01098E01
    Inspect the commutator for an open circuit.

    1. Using an ohmmeter, check that there is resistance between the segments of the commutator.

      Standard:
      1 Ω or lower

      1. If the result is not as specified, replace the armature assembly.

  1. ST01099E01
    Inspect the commutator for a short circuit.

    1. Using an ohmmeter, check that there is no resistance between the commutator and armature core.

      Standard:
      10 kΩ higher

      1. If the result is not as specified, replace the armature assembly.

  1. S004640E01
    Inspect the commutator circle runout.

    1. Place the armature on the V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.0020 in.)

      1. If the runout is greater than the maximum, correct with sandpaper (#400) or replace the armature assembly.

  1. ST01100E01
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    35.0 mm (1.378 in.)

    Minimum diameter:
    34.0 mm (1.339 in.)

    1. If the diameter is less than the minimum, replace the armature assembly.

  1. ST00040E01
    Measure the undercut depth of the commutator.

    Standard depth:
    0.7 mm (0.028 in.)

    Minimum depth:
    0.2 mm (0.008 in.)

    1. If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  1. Inspect the bearings.

    1. Check that the bearing rotates smoothly.

      1. If necessary, replace them.


INSPECT STARTER YOKE ASSEMBLY

  1. B000453E01
    Inspect for an open circuit.

    1. Check that there is continuity between the terminal C wire and brushes.

      Standard:
      1 Ω or lower

      1. If the result not as specified, replace the starter yoke assembly.

  1. B000454E01
    Inspect for a short circuit.

    1. Check that there is no continuity between the terminal C wire and starter yoke body.

    2. Check that there is no continuity between the brushes and stater yoke body.

      Standard:
      10 kΩ or higher

      1. If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

  1. B000900E01
    Using vernier calipers, measure the brush length.

    Standard brush length:
    16.5 mm (0.650 in.)

    Minimum brush length:
    9.0 mm (0.354 in.)

    1. If the length is less than the minimum, replace the brush holder and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. P021088E01
    Using an ohmmeter, check that there is continuity between the positive and negative brush holders.

    Standard:
    10 kΩ or higher

    1. If the result is not as specified, replace the brush holder.

  1. ST00019E02
    Using a pull scale, measure the brush spring load.

    Standard spring load:
    26.5 to 32.3 N (2.7 to 3.3 kgf, 6.0 to 7.3 lbf)

    Minimum spring load:
    17.6 N (1.8 kgf, 4.0 lbf)

    1. If the spring load is less than the minimum, replace the brush springs.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. P010821E01
    Check that the starter clutch operates.
    1. If the starter clutch does not operate, replace it.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A074034E01
    Inspect the pull-in coil resistance.

    1. Using an ohmmeter, check that there is continuity between terminals 50 and C.

      Standard:
      1 Ω or lower

      1. If the result is not as specified, replace the magnet starter switch assembly.

  1. A074035E01
    Inspect the holding coil continuity.

    1. Using an ohmmeter, check that there is continuity between terminals 50 and body.

      Standard:
      2 Ω or lower

      1. If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →