B1900/73 Short in Front Driver Side Pretensioner Squib Circuit
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Also covers:
- B1901/73 Open in Front Driver Side Pretensioner Squib Circuit
- B1902/73 Short to GND in Front Driver Side Pretensioner Squib Circuit
- B1903/73 Short to B+ in Front Driver Side Pretensioner Squib Circuit
DESCRIPTION
The driver side front pretensioner squib circuit consists of the center airbag sensor assembly and the front seat outer belt assembly.This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side front pretensioner squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1900/73 |
|
|
| B1901/73 |
|
|
| B1902/73 |
|
|
| B1903/73 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
- After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SIDE FRONT PRETENSIONER SQUIB) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
LHD
Disconnect the connector from the front seat outer belt assembly LH.
RHD
Disconnect the connector from the front seat outer belt assembly RH.
Connect the white wire side of SST (resistance 2.1 Ω) to connector "C".
- CAUTION:
- Never connect a tester to the front seat outer belt assembly (Driver side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector.
- Insert the SST straight into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector.
- SST
- 09843-18060
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1900, B1901, B1902, B1903 or 73 is not output.
- HINT:
- Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector "C".
Check that the engine room main wire connector (on the front seat outer belt assembly side) is not damaged.
- OK:
- The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK ENGINE ROOM MAIN WIRE (DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT) |
Disconnect the connectors from the center airbag sensor assembly.

Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Voltage:
Tester connection
Condition
Specified condition
B23-1 (L+) -
Body ground (LHD)
Ignition switch ON
Below 1 V
B23-2 (L-) -
Body ground (LHD)
Ignition switch ON
Below 1 V
B25-1 (R+) -
Body ground (RHD)
Ignition switch ON
Below 1 V
B25-2 (R-) -
Body ground (RHD)
Ignition switch ON
Below 1 V
Check for open in the circuit.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester connection
Condition
Specified condition
B23-1 (L+) -
B23-2 (L-) (LHD)
Always
Below 1 Ω
B25-1 (R+) -
B25-2 (R-) (RHD)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester connection
Condition
Specified condition
B23-1 (L+) -
Body ground (LHD)
Always
1 MΩ or higher
B23-2 (L-) -
Body ground (LHD)
Always
1 MΩ or higher
B25-1 (R+) -
Body ground (RHD)
Always
1 MΩ or higher
B25-2 (R-) -
Body ground (RHD)
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector "B" (Click here).
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester connection
Condition
Specified condition
B23-1 (L+) -
B23-2 (L-) (LHD)
Always
1 MΩ or higher
B25-1 (R+) -
B25-2 (R-) (RHD)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the connectors to the front seat outer belt assembly and the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1900, B1901, B1902, B1903 or 73 is not output.
- HINT:
- Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
