2014-2019 Hiace · Service Manual RESTRAINTS

B1900/73 Short in Front Pretensioner Squib RH Circuit

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The front pretensioner RH circuit consists of the center airbag sensor assembly and front seat outer belt RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1900/73
One of the following conditions is met:
  1. The center airbag sensor assembly detects a line short circuit signal 5 times in the front pretensioner RH circuit during the primary check.
  2. A front pretensioner RH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly RH
  3. Center airbag sensor assembly
B1901/73
One of the following conditions is met:
  1. The center airbag sensor assembly detects an open circuit signal in the front pretensioner RH circuit for 2 seconds.
  2. A front pretensioner RH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly RH
  3. Center airbag sensor assembly
B1902/73
One of the following conditions is met:
  1. The center airbag sensor assembly detects a short circuit to ground signal in the front pretensioner RH circuit for 0.5 seconds.
  2. A front pretensioner RH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly RH
  3. Center airbag sensor assembly
B1903/73
One of the following conditions is met:
  1. The center airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner RH circuit for 0.5 seconds.
  2. A front pretensioner RH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly RH
  3. Center airbag sensor assembly

WIRING DIAGRAM

C324736E04

INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After replacing the center airbag sensor assembly, refer to initialization (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the GTS (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK FRONT SEAT OUTER BELT RH

  1. C205409E13
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat outer belt RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt RH for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly RH
    *2
    Center Airbag Sensor Assembly
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Front Seat Outer Belt Assembly RH)

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.



NG
Go to step 2
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)

2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. C208250E04
    Check that the connectors (on the center airbag sensor assembly side and front seat outer belt RH side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly RH
    *2
    Engine Room Main Wire
    *3
    Center Airbag Sensor Assembly



NG
REPLACE ENGINE ROOM MAIN WIRE
OK


3. CHECK ENGINE ROOM MAIN WIRE

  1. C205410E13
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B25-1 (R+) - Body ground
    Ignition switch ON
    Below 1 V
    B25-2 (R-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B25-1 (R+) - B25-2 (R-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B25-1 (R+) - B25-2 (R-)
    Always
    1 MΩ or higher
    B25-1 (R+) - Body ground
    Always
    1 MΩ or higher
    B25-2 (R-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Seat Outer Belt Assembly RH
*2
Engine Room Main Wire
*3
Center Airbag Sensor Assembly
*4
Connector C
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


NG
REPLACE ENGINE ROOM MAIN WIRE
OK


4. CHECK DTC

  1. C198556E02
    Connect the connectors to the front seat outer belt RH and center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly RH
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (Apr 2016 – Dec 2016)B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Oct 2014 – Dec 2014) →