2014-2019 Hiace · Service Manual RESTRAINTS

B1905/74 Short in Front Pretensioner Squib LH Circuit

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The front pretensioner LH circuit consists of the center airbag sensor assembly and front seat outer belt LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner LH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1905/74
One of the following conditions is met:
  1. The center airbag sensor assembly detects a line short circuit signal 5 times in the front pretensioner LH circuit during the primary check.
  2. A front pretensioner LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly LH
  3. Center airbag sensor assembly
B1906/74
One of the following conditions is met:
  1. The center airbag sensor assembly detects an open circuit signal in the front pretensioner LH circuit for 2 seconds.
  2. A front pretensioner LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly LH
  3. Center airbag sensor assembly
B1907/74
One of the following conditions is met:
  1. The center airbag sensor assembly detects a short circuit to ground signal in the front pretensioner LH circuit for 0.5 seconds.
  2. A front pretensioner LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly LH
  3. Center airbag sensor assembly
B1908/74
One of the following conditions is met:
  1. The center airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner LH circuit for 0.5 seconds.
  2. A front pretensioner LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Engine room main wire
  2. Front seat outer belt assembly LH
  3. Center airbag sensor assembly

WIRING DIAGRAM

C324736E03

INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After replacing the center airbag sensor assembly, refer to initialization (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the GTS (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK FRONT SEAT OUTER BELT LH

  1. C205411E13
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat outer belt LH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt LH for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907 or B1908 is not output.

    HINT:
    Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Front Seat Outer Belt Assembly LH)

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.



NG
Go to step 2
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)

2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Turn the ignition switch to ON.

  1. C208251E04
    Check that the connectors (on the center airbag sensor assembly side and front seat outer belt LH side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Engine Room Main Wire
    *3
    Center Airbag Sensor Assembly



NG
REPLACE ENGINE ROOM MAIN WIRE
OK


3. CHECK ENGINE ROOM MAIN WIRE

  1. C205412E13
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B23-1 (L+) - Body ground
    Ignition switch ON
    Below 1 V
    B23-2 (L-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (L+) - B23-2 (L-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (L+) - B23-2 (L-)
    Always
    1 MΩ or higher
    B23-1 (L+) - Body ground
    Always
    1 MΩ or higher
    B23-2 (L-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Seat Outer Belt Assembly LH
*2
Engine Room Main Wire
*3
Center Airbag Sensor Assembly
*4
Connector C
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


NG
REPLACE ENGINE ROOM MAIN WIRE
OK


4. CHECK DTC

  1. C207519E04
    Connect the connectors to the front seat outer belt LH and center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907 or B1908 is not output.

    HINT:
    Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Oct 2014 – Dec 2014)B1905/74 Short in Front Pretensioner Squib LH Circuit (+ B1906/74, B1907/74, B1908/74) (Apr 2016 – Dec 2016) →