INSPECTION
Inspection · Vehicles built from Oct 2014
| INSPECT STARTER |


- NOTICE:
- These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.
Perform pull-in/holding test.
Remove the nut and disconnect the field coil lead wire from terminal C.
Connect the battery to the magnet starter switch assembly as shown in the illustration. Then check that the clutch pinion gear moves outward.


Disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.


If the result is not as specified, replace the magnet starter switch assembly.
Perform operation test without load.
Install the field coil lead wire with the nut to the terminal C.
- Torque:
- 5.9 N*m{ 60 kgf*cm , 52 in.*lbf }
Mount the starter in a vise.
Connect the battery and ammeter to the starter as shown in the illustration.
Check that the starter rotates smoothly and steadily while the pinion gear is out. Then measure the current.


- Standard current:
- 120 A or less at 11.5 V
| INSPECT STARTER ARMATURE ASSEMBLY |
Check the resistance.

Measure the resistance between any 2 segments of the commutator.
- Standard resistance:
- Below 1 Ω
Measure the resistance between a segment of the commutator and armature coil core.

- Standard resistance:
- 10 kΩ or higher
Inspect the commutator for circle runout.

Place the armature on V-blocks.
Using a dial gauge, measure the circle runout.
- Maximum circle runout:
- 0.05 mm (0.0020 in.)
Using a vernier caliper, measure the commutator diameter.

- Standard commutator diameter:
- 35.0 mm (1.378 in.)
- Minimum commutator diameter:
- 34.0 mm (1.339 in.)
Using a vernier caliper, measure the undercut depth of the commutator.

- Standard undercut depth:
- 0.7 mm (0.028 in.)
- Minimum undercut depth:
- 0.2 mm (0.008 in.)
Inspect the bearings.
Check that the bearings rotate smoothly. If the result is not as specified, replace the starter armature assembly.
| INSPECT STARTER YOKE ASSEMBLY |
Inspect the field coil for open circuit.

Measure the resistance between the lead wire and field coil brush lead.
- Standard resistance:
- Below 1 Ω
Inspect the field coil for ground.

Measure the resistance between the terminal C wire and starter yoke body.
Measure the resistance between the brushes and starter yoke body.
- Standard resistance:
- 10 kΩ or higher
| INSPECT BRUSH |
![]() ![]() |
Using a vernier caliper, measure the brush length.
- Standard length:
- 16.5 mm (0.650 in.)
- Minimum length:
- 9.0 mm (0.354 in.)
| INSPECT STARTER BRUSH HOLDER ASSEMBLY |
Inspect the brush insulation.

Using an ohmmeter, measure the resistance between the positive and negative brush holders.
- Standard resistance:
- 10 kΩ or higher
Take the pull scale reading the instant the brush spring separates from the brush.

- Standard spring installed load:
- 26.5 to 32.3 N (2.7 to 3.3 kgf, 5.9 to 7.3 lbf)
- Minimum spring installed load:
- 17.6 N (1.8 kgf, 4.0 lbf)
| INSPECT STARTER CLUTCH SUB-ASSEMBLY |
Rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If necessary, replace the starter clutch subassembly.
| INSPECT MAGNET STARTER SWITCH ASSEMBLY |
Check the pull-in coil for open circuit.

Measure the resistance between terminals 50 and C.
- Standard resistance:
- Below 1 Ω
Check the hold-in coil for open circuit.

Measure the resistance between terminal 50 and the switch body.
- Standard resistance:
- Below 2 Ω

