2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with 400-grit sandpaper or a lathe.

  1. A122065E05
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. A122066E05
    Inspect the commutator for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Armature coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Segment
      *b
      Armature Coil Core
      If the result is not as specified, replace the starter armature assembly.

  1. A300395
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    29.0 mm (1.14 in.)

    Minimum diameter:
    28.0 mm (1.10 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A122067
    Check the commutator circle runout.

    1. Place the shaft of the starter armature on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum commutator runout:
      0.05 mm (0.00197 in.)

      If the runout is more than the maximum, replace the starter armature assembly.

  1. A115027
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Using a vernier caliper, measure the brush length.

    A300396E02

    Text in Illustration 
    *a
    Brush
    *b
    Spring
    *c
    Length
    -
    -

    Standard length:
    14.4 mm (0.567 in.)

    Minimum length:
    9.0 mm (0.354 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.

  1. ST00019E16
    Inspect the load of the brush spring.

    1. Take a pull scale reading immediately after the brush spring separates from the brush.

      Standard spring load:
      16 to 20 N (1.7 to 2.0 kgf, 3.6 to 4.5 lbf)

      Minimum spring load:
      6.7 N (0.7 kgf, 1.5 lbf)

      Text in Illustration 
      *a
      Brush
      *b
      Brush Spring
      If the load is less than the minimum, replace the starter brush holder assembly.

  1. A300397E01
    Inspect the insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive brush holder - Negative brush holder
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Check the gear teeth of the planetary gears and starter center bearing clutch for wear or damage.
    If any planetary gear is damaged, replace the planetary gear assembly.
    If any gear of the starter center bearing clutch is damaged, replace the starter center bearing clutch sub-assembly.

  1. A221357
    Check the movement of the clutch pinion gear.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock

    1. Rotate the clutch pinion gear clockwise and check that it turns freely.

    2. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
      If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A300398
    Push in the plunger and check that it returns quickly to its original position.
    If the result is not as specified, replace the magnet starter switch assembly.

  1. A194284E06
    Check the pull-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Terminal 50
      *b
      Terminal C
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A194285E06
    Check the hold-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *a
      Terminal 50
      *b
      Switch Body
      If the result is not as specified, replace the magnet starter switch assembly.

← INSPECTION (Oct 2014 – Dec 2014)REASSEMBLY (Oct 2014 – Dec 2014) →