2014-2019 Hiace · Service Manual ENGINE

P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The G2 signal plate has 3 teeth on its outer circumference and is installed on the exhaust camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.
P0016 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle engine for 5 seconds or more
Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm occurs a certain number of times.
(1 trip detection logic)
  1. Camshaft position sensor
  2. Crankshaft position sensor
  3. Exhaust camshaft
  4. ECM
P0340 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Crank engine for 4 seconds
STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more.
(2 trip detection logic)
  1. Camshaft position sensor
  2. Exhaust camshaft
  3. ECM
Idle engine for 1 second or more
STA off:
Camshaft position sensor signal is not input with an engine speed of 650 rpm or more.
(1 trip detection logic)

HINT:
  1. If DTC P0016 or P0340 is stored, the following symptoms may appear:
    1. Difficulty starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power

Reference: Inspection using an oscilloscope.
A340471E01

HINT:
The correct waveform is as shown.
ECM Terminal Name
Between G2+ and G2-
Between NE+ and NE-
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling after engine warmed


WIRING DIAGRAM

A348533E04

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Cranking is OK
    A
    Does not crank at all
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A


2. CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. A316078E02
    Check the sensor installation.
    Text in Illustration 
    *a
    Clearance

    OK:
    Camshaft position sensor is installed correctly.



NG
Go to step 9
OK


3. INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Inspect the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.



NG
Go to step 8
OK


4. CHECK ENGINE MECHANICAL SYSTEM
  1. When the G2 signal appears to be malfunctioning, check the exhaust camshaft.

    1. If the teeth of the timing rotor are damaged, perform replacement (Click here).

  1. When the Ne signal appears to be malfunctioning, check the following parts.

    1. Installation condition of the crankshaft position sensor.
    2. Crank angle sensor plate.

  1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain (Click here).


NEXT


5. REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).



NEXT
Go to step 6
6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0016 or P0340 is output
    A
    DTC is not output
    B



B
END
A


7. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10
8. REPLACE EXHAUST CAMSHAFT
  1. Replace the exhaust camshaft.



NEXT
Go to step 10
9. SECURELY REINSTALL CAMSHAFT POSITION SENSOR
  1. Securely reinstall the camshaft position sensor.


NEXT


10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output.


NEXT

END


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2017)P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032) (from Jan 2017) →